Under Construction!
This page is currently under construction. You can edit the article to help completing it.
Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.
OpenWrt support
Not supported.
Hardware highlights
| SoC | CPU MHz | Flash MB | RAM MB | WLAN2.4 | WLAN5.0 | Gbit ports | USB | Serial | JTag |
|---|---|---|---|---|---|---|---|---|---|
| Qualcomm Atheros IPQ6018LA | 1800 | 256NAND | 512 | b/g/n | n/ac/ax | 5 | 1x 3.0 | Yes | Yes |
Hardware
Info
| Architecture | ARM |
|---|---|
| Vendor | Linksys |
| Bootloader | U-Boot |
| CPU/Speed | Qualcomm Atheros IPQ6000 1.2 GHz |
| Flash-Chip | unkown |
| Flash size | 256 MiB |
| RAM | 512 MiB |
| Wireless | 2.4G QCN5022 2×2, 5G QCN5052 2×2, 2.4G SKY85340-11, 5G SKY85755-11 |
| Bluetooth | Antenna and radio present, but not activated |
| Ethernet | 10/100/1000 Mbit/s w/ vlan support |
| USB | 1x 3.0 |
| Serial | Yes -> baud rate 115200 |
| JTAG | Yes |
Photos
Opening the case
Four screws total:
The first and second screws are under the front feet
The third and forth screws are under the label
The top is secured with interior plastic tabs
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
| Serial connection parameters for Linksys MR7350 1.0 | Baud Rate 115200, UART using FT232R to USB |
|---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootlogs
OEM bootlog v1.1.7
Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2S - IMAGE_VARIANT_STRING=IPQ6018LAS - OEM_IMAGE_VERSION_STRING=crm-ubuntu64S - Boot Interface: NANDS - Secure Boot: OffS - Boot Config @ 0x000a602c = 0x000002e5S - JTAG ID @ 0x000a607c = 0x001390e1S - OEM ID @ 0x000a6080 = 0x00000000S - Serial Number @ 0x000a4128 = 0xfe655252S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009S - PBL Patch Ver: 1S - I-cache: OnS - D-cache: OnB - 3413 - PBL, StartB - 592 - bootable_media_detect_entry, StartB - 4340 - bootable_media_detect_success, StartB - 5148 - elf_loader_entry, StartB - 5320 - auth_hash_seg_entry, StartB - 7787 - auth_hash_seg_exit, StartB - 8283 - elf_segs_hash_verify_entry, StartB - 110430 - elf_segs_hash_verify_exit, StartB - 114854 - auth_xbl_sec_hash_seg_entry, StartB - 114997 - auth_xbl_sec_hash_seg_exit, StartB - 121544 - xbl_sec_segs_hash_verify_entry, StartB - 121545 - xbl_sec_segs_hash_verify_exit, StartB - 122475 - PBL, EndB - 103242 - SBL1, StartB - 243329 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4B - 245769 - clock_init, StartD - 2806 - clock_init, DeltaB - 254339 - boot_flash_init, StartD - 26169 - boot_flash_init, DeltaB - 283711 - sbl1_ddr_set_default_params, StartD - 244 - sbl1_ddr_set_default_params, DeltaB - 290329 - boot_config_data_table_init, StartD - 4758 - boot_config_data_table_init, Delta - (575 Bytes)B - 300150 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0B - 305000 - Image Load, StartD - 6588 - OEM_MISC Image Loaded, Delta - (0 Bytes)B - 314333 - Image Load, StartD - 5063 - PMIC Image Loaded, Delta - (0 Bytes)B - 322202 - sbl1_ddr_set_params, StartB - 327173 - CPR configuration: 0x366B - 330376 - Pre_DDR_clock_init, StartD - 213 - Pre_DDR_clock_init, DeltaD - 0 - sbl1_ddr_set_params, DeltaB - 367037 - Image Load, StartD - 427 - APDP Image Loaded, Delta - (0 Bytes)B - 380121 - Image Load, StartD - 427 - QTI_MISC Image Loaded, Delta - (0 Bytes)B - 382561 - Image Load, StartD - 823 - Auth MetadataD - 732 - Segments hash checkD - 22235 - QSEE Dev Config Image Loaded, Delta - (36354 Bytes)B - 406748 - Image Load, StartD - 6558 - Auth MetadataD - 10644 - Segments hash checkD - 329186 - QSEE Image Loaded, Delta - (1470632 Bytes)B - 736392 - Image Load, StartD - 671 - Auth MetadataD - 1067 - Segments hash checkD - 34587 - RPM Image Loaded, Delta - (102664 Bytes)B - 772687 - Image Load, StartD - 702 - Auth MetadataD - 3202 - Segments hash checkD - 118828 - APPSBL Image Loaded, Delta - (561320 Bytes)B - 907131 - SBL1, EndD - 804194 - SBL1, DeltaS - Flash Throughput, 5000 KB/s (2171545 Bytes, 422232 us)S - Core 0 Frequency, 800 MHzS - DDR Frequency, 466 MHzU-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800)CBT U-Boot ver: 2.3.01 ([IPQ6018].[SPF11.CSU1].[code version])DRAM: smem ram ptable found: ver: 2 len: 4512 MiBNAND: ONFI device foundID = 1590aac2Vendor = c2Device = aaSF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)256 MiBMMC: sdhci: Node Not found, skipping initializationPCI0 is not defined in the device treeIn: serial@78B1000Out: serial@78B1000Err: serial@78B1000machid: 8030200eth0 MAC Address from ART is not valideth1 MAC Address from ART is not valideth2 MAC Address from ART is not valideth3 MAC Address from ART is not valideth4 MAC Address from ART is not valideth5 MAC Address from ART is not validUpdating boot_count ... doneHit any key to stop autoboot: 1 0 Setting bus to 0Valid chip addresses: 62 70NAND read: device 0 offset 0x6680000, size 0x800000 8388608 bytes read: OK## Loading kernel from FIT Image at 44000000 ...
Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM Linksys Linux-4.4.60 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e4 Data Size: 4712968 Bytes = 4.5 MiB Architecture: ARM OS: Linux Load Address: 0x41008000 Entry Point: 0x41008000 Hash algo: crc32 Hash value: 4a216b6c Hash algo: sha1 Hash value: 2ee4bf63c32cb756c17d5cfdafb36fb1504568e3 Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM Linksys Elise device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x4447ec1c Data Size: 73850 Bytes = 72.1 KiB Architecture: ARM Hash algo: crc32 Hash value: e7d6edd5 Hash algo: sha1 Hash value: 54f4c5f01ed076d76b7f00a5968a664cf4eed54e Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x4447ec1c Uncompressing Kernel Image ... OK Loading Device Tree to 484ea000, end 484ff079 ... OK
Could not find PCI in device treeUsing machid 0x8030200 from environmentStarting kernel ...[ 0.000000] Booting Linux on physical CPU 0x0[ 0.000000] Initializing cgroup subsys cpuset[ 0.000000] Initializing cgroup subsys cpu[ 0.000000] Initializing cgroup subsys cpuacct[ 0.000000] Linux version 4.4.60 (root@build-vm) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r35193) ) #1 SMP PREEMPT Fri Dec 3 16:50:07 PST 2021[ 0.000000] CPU: ARMv7 Processor [51af8014] revision 4 (ARMv7), cr=10c0383d[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache[ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ6018/AP-CP03-C1[ 0.000000] Ignoring memory range 0x40000000 - 0x41000000[ 0.000000] Memory policy: Data cache writealloc[ 0.000000] psci: probing for conduit method from DT.[ 0.000000] psci: PSCIv1.0 detected in firmware.[ 0.000000] psci: Using standard PSCI v0.2 function IDs[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.[ 0.000000] PERCPU: Embedded 11 pages/cpu @9eb3a000 s15424 r8192 d21440 u45056[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 109988[ 0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait swiotlb=1 coherent_pool=2M[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)[ 0.000000] Memory: 427400K/444416K available (7381K kernel code, 459K rwdata, 2184K rodata, 1024K init, 456K bss, 17016K reserved, 0K cma-reserved, 0K highmem)[ 0.000000] Virtual kernel memory layout:[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)[ 0.000000] vmalloc : 0x9f800000 - 0xff800000 (1536 MB)[ 0.000000] lowmem : 0x80000000 - 0x9f000000 ( 496 MB)[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)[ 0.000000] .text : 0x80008000 - 0x80a57450 (10558 kB)[ 0.000000] .init : 0x80b00000 - 0x80c00000 (1024 kB)[ 0.000000] .data : 0x80c00000 - 0x80c72fd8 ( 460 kB)[ 0.000000] .bss : 0x80c75000 - 0x80ce7098 ( 457 kB)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1[ 0.000000] Preemptible hierarchical RCU implementation.[ 0.000000] Build-time adjustment of leaf fanout to 32.[ 0.000000] NR_IRQS:16 nr_irqs:16 16[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns[ 0.000016] Switching to timer-based delay loop, resolution 41ns[ 0.000478] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)[ 0.000490] pid_max: default: 32768 minimum: 301[ 0.000581] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.000590] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.001113] Initializing cgroup subsys io[ 0.001128] Initializing cgroup subsys memory[ 0.001151] Initializing cgroup subsys devices[ 0.001165] Initializing cgroup subsys freezer[ 0.001175] Initializing cgroup subsys net_cls[ 0.001185] Initializing cgroup subsys pids[ 0.001207] CPU: Testing write buffer coherency: ok[ 0.001590] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000[ 0.001640] Setting up static identity map for 0x41100000 - 0x41100058[ 0.054106] MSM Memory Dump base table set up[ 0.054131] MSM Memory Dump apps data table set up[ 0.090233] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001[ 0.120219] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002[ 0.150254] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003[ 0.150308] Brought up 4 CPUs[ 0.150327] SMP: Total of 4 processors activated (192.00 BogoMIPS).[ 0.150333] CPU: All CPU(s) started in SVC mode.[ 0.169938] VFP support v0.3: implementor 51 architecture 3 part 40 variant 3 rev 4[ 0.170253] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns[ 0.170277] futex hash table entries: 1024 (order: 4, 65536 bytes)[ 0.170634] pinctrl core: initialized pinctrl subsystem[ 0.171710] NET: Registered protocol family 16[ 0.172813] DMA: preallocated 2048 KiB pool for atomic coherent allocations[ 0.200085] cpuidle: using governor ladder[ 0.230103] cpuidle: using governor menu[ 0.230348] NET: Registered protocol family 42[ 0.245869] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.248889] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.258587] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.[ 0.258596] hw-breakpoint: maximum watchpoint size is 8 bytes.[ 0.260212] CPU: IPQ6018, SoC Version: 1.0[ 0.260996] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 0.262229] IPC logging disabled[ 0.262235] IPC logging disabled[ 0.262240] IPC logging disabled[ 0.262245] IPC logging disabled[ 0.262250] IPC logging disabled[ 0.262459] sps:sps is ready.[ 0.290950] socinfo_select_format: Unsupported format v0.13. Falling back to v0.12.[ 0.290972] socinfo_print: v0.12, id=402, ver=1.0, raw_id=313, raw_ver=0, hw_plat=8, hw_plat_ver=196610[ 0.290972] accessory_chip=0, hw_plat_subtype=0, pmic_model=0, pmic_die_revision=0 foundry_id=2 serial_number=4268053074 num_pmics=0 chip_family=0x0 raw_device_family=0x2 raw_device_number=0x17[ 0.291901] usbcore: registered new interface driver usbfs[ 0.291963] usbcore: registered new interface driver hub[ 0.292033] usbcore: registered new device driver usb[ 0.292135] pps_core: LinuxPPS API ver. 1 registered[ 0.292142] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it[ 0.292168] PTP clock support registered[ 0.294166] rpmsg_dev_probe: No pm domain[ 0.295646] Bluetooth: Core ver 2.21[ 0.295683] NET: Registered protocol family 31[ 0.295690] Bluetooth: HCI device and connection manager initialized[ 0.295702] Bluetooth: HCI socket layer initialized[ 0.295712] Bluetooth: L2CAP socket layer initialized[ 0.295736] Bluetooth: SCO socket layer initialized[ 0.296008] clocksource: Switched to clocksource arch_sys_counter[ 0.298840] NET: Registered protocol family 2[ 0.299358] TCP established hash table entries: 4096 (order: 2, 16384 bytes)[ 0.299407] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)[ 0.299482] TCP: Hash tables configured (established 4096 bind 4096)[ 0.299519] UDP hash table entries: 256 (order: 1, 8192 bytes)[ 0.299542] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)[ 0.299693] NET: Registered protocol family 1[ 0.300882] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available[ 0.309307] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.309328] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.[ 0.313236] Key type asymmetric registered[ 0.313250] Asymmetric key parser 'x509' registered[ 0.313285] io scheduler noop registered[ 0.313298] io scheduler deadline registered (default)[ 0.321374] NET: Registered protocol family 27[ 0.321386] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled[ 0.321402] qmi_log_init: IPC Logging disabled[ 0.321408] qmi_log_init: IPC Logging disabled[ 0.321546] msm_rpm_log_probe: OK[ 0.321872] msm-dcc b3000.dcc: DCC XPU is not specified[ 0.322119] msm-dcc b3000.dcc: jiffies_64: 0xffff8aef, cntvct_64: 0x685d06c[ 0.322132] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0x9fa2c004)[ 0.322143] msm-dcc b3000.dcc: gcnt_lo: 0x0685d2d1(0x9fa2c000)[ 0.322923] scm_call failed: func id 0x2000120 ret: -1 syscall returns: 0x0, 0x0, 0x0[ 0.322931] TZ SMMU State: Can't detect SMMU State[ 0.322983] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set[ 0.323198] rpmsg_dev_probe: No pm domain[ 0.324097] msm_serial 78b0000.serial: msm_serial: detected port #1[ 0.324131] msm_serial 78b0000.serial: uartclk = 24000000[ 0.324164] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 20, base_baud = 1500000) is a MSM[ 0.324494] msm_serial 78b1000.serial: msm_serial: detected port #0[ 0.324526] msm_serial 78b1000.serial: uartclk = 1843200[ 0.324557] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 21, base_baud = 115200) is a MSM[ 0.324572] msm_serial: console setup on port #0[ 1.102366] console [ttyMSM0] enabled[ 1.107421] msm_serial: driver initialized[ 1.110922] msm_serial_hsl_init: driver initialized[ 1.124149] brd: module loaded[ 1.129652] loop: module loaded[ 1.130296] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64[ 1.133259] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00, 0, 0[ 1.139689] QPIC controller hw version Major:1, Minor:5[ 1.145507] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa[ 1.150405] nand: ONFI 10-Compliant Macronix MX30UF2G18AC[ 1.156958] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64[ 1.162332] 20 ofpart partitions found on MTD device qcom_nand.0[ 1.169718] Creating 20 MTD partitions on “qcom_nand.0”:[ 1.175870] 0x000000000000-0x000000180000 : “0:SBL1”[ 1.183218] 0x000000180000-0x000000280000 : “0:MIBIB”[ 1.187726] 0x000000280000-0x000000600000 : “0:QSEE”[ 1.194476] 0x000000600000-0x000000680000 : “0:DEVCFG”[ 1.197234] 0x000000680000-0x000000700000 : “0:RPM”[ 1.202174] 0x000000700000-0x000000780000 : “0:CDT”[ 1.206988] 0x000000780000-0x000000800000 : “0:APPSBLENV”[ 1.211853] 0x000000800000-0x000000980000 : “0:APPSBL”[ 1.218182] 0x000000980000-0x000000a00000 : “0:ART”[ 1.222457] 0x000000a00000-0x000001300000 : “0:WIFIFW”[ 1.233414] 0x000001300000-0x000001380000 : “0:ETHPHYFW”[ 1.234625] 0x000001380000-0x000001400000 : “u_env”[ 1.238917] 0x000001400000-0x000001440000 : “s_env”[ 1.243322] 0x000001440000-0x000001480000 : “devinfo”[ 1.248215] 0x000001480000-0x000006680000 : “kernel”[ 1.314612] 0x000001c80000-0x000006680000 : “rootfs”[ 1.370514] mtd: device 15 (rootfs) set to be root filesystem[ 1.370772] mtdsplit: no squashfs found in “rootfs”[ 1.375238] 0x000006680000-0x00000b880000 : “alt_kernel”[ 1.441803] 0x000006e80000-0x00000b880000 : “alt_rootfs”[ 1.497988] 0x00000b880000-0x00000ba80000 : “sysdiag”[ 1.500291] 0x00000ba80000-0x00000fe80000 : “syscfg”[ 1.554174] libphy: Fixed MDIO Bus: probed[ 1.774941] qca-mdio 90000.mdio: Could not find phy-reset-gpio[ 1.775082] libphy: qca_mdio: probed[ 1.780916] qca-mdio 90000.mdio: qca-mdio driver was registered[ 1.783522] PPP generic driver version 2.4.2[ 1.789181] NET: Registered protocol family 24[ 1.793547] PPTP driver version 0.8.5[ 1.797992] Unable to create IPC log context![ 1.802083] cnss[2]: INFO: Platform driver probed successfully. plat 9dfe8010 tgt 0xfffd[ 1.806519] dummy_hcd dummy_hcd.0: USB Host+Gadget Emulator, driver 02 May 2005[ 1.814041] dummy_hcd dummy_hcd.0: Dummy host controller[ 1.821103] dummy_hcd dummy_hcd.0: new USB bus registered, assigned bus number 1[ 1.827262] hub 1-0:1.0: USB hub found[ 1.834024] hub 1-0:1.0: 1 port detected[ 1.838220] i2c /dev entries driver[ 1.876520] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com[ 1.876561] Bluetooth: HCI UART driver ver 2.3[ 1.884015] Bluetooth: HCI UART protocol H4 registered[ 1.888289] Bluetooth: HCI UART protocol BCSP registered[ 1.893841] sdhci: Secure Digital Host Controller Interface driver[ 1.898878] sdhci: Copyright© Pierre Ossman[ 1.904854] sdhci-pltfm: SDHCI platform and OF driver helper[ 1.910299] leds-pca963x 0-0062: PCA963X_HW_BLINK ON[ 1.917387] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed[ 1.920016] ICE IRQ = 32[ 1.928636] [ 1.928636] Version Rollback Feature Disabled[ 1.931388] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x08b04000[ 1.936572] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x08b04000[ 1.952351] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x08b04000[ 1.966845] sps:BAM 0x08b04000 is registered.[ 1.975574] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss[ 1.977629] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available[ 1.986777] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000[ 1.992883] coresight-csr 6001000.csr: CSR initialized[ 2.000604] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000[ 2.005578] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000[ 2.013135] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000[ 2.020502] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000[ 2.027868] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000[ 2.035227] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000[ 2.042625] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000[ 2.050087] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000[ 2.057385] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000[ 2.064746] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000[ 2.072145] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000[ 2.079518] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000[ 2.086905] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000[ 2.094259] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000[ 2.101667] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000[ 2.109036] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000[ 2.116423] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000[ 2.123921] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000[ 2.131316] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000[ 2.138727] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000[ 2.146146] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000[ 2.153458] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06064000[ 2.160516] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06064000[ 2.176225] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06064000[ 2.190717] sps:BAM 0x06064000 is registered.[ 2.197741] coresight-tmc 6048000.tmc: TMC initialized[ 2.201816] coresight-tmc 6047000.tmc: TMC initialized[ 2.206969] coresight-funnel 6041000.funnel: FUNNEL initialized[ 2.211967] coresight-funnel 6100000.funnel: FUNNEL initialized[ 2.217796] coresight-funnel 6130000.funnel: FUNNEL initialized[ 2.223679] coresight-funnel 6120000.funnel: FUNNEL initialized[ 2.229614] coresight-funnel 61a1000.funnel: FUNNEL initialized[ 2.236241] coresight-etm4x 619c000.etm: ETM 4.0 initialized[ 2.241854] coresight-etm4x 619d000.etm: ETM 4.0 initialized[ 2.247821] coresight-etm4x 619e000.etm: ETM 4.0 initialized[ 2.253494] coresight-etm4x 619f000.etm: ETM 4.0 initialized[ 2.258635] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized[ 2.264357] coresight-stm 6002000.stm: STM initialized[ 2.273015] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000[ 2.276786] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized[ 2.284797] u32 classifier[ 2.291924] input device check on[ 2.294428] Actions configured[ 2.298207] Netfilter messages via NETLINK v0.30.[ 2.301484] nfnl_acct: registering with nfnetlink.[ 2.306297] nf_conntrack version 0.5.0 (6678 buckets, 26712 max)[ 2.311349] ctnetlink v0.93: registering with nfnetlink.[ 2.317178] nf_conntrack_rtsp v0.7 loading[ 2.322443] nf_tables: © 2007-2009 Patrick McHardy kaber@trash.net[ 2.326330] nf_tables_compat: © 2012 Pablo Neira Ayuso pablo@netfilter.org[ 2.333140] xt_time: kernel timezone is -0000[ 2.340029] ip_set: protocol 6[ 2.344623] gre: GRE over IPv4 demultiplexor driver[ 2.347404] ip_gre: GRE over IPv4 tunneling driver[ 2.353273] nf_nat_rtsp v0.7 loading[ 2.357143] ip_tables: (C) 2000-2006 Netfilter Core Team[ 2.360943] arp_tables: (C) 2002 David S. Miller[ 2.366837] NET: Registered protocol family 10[ 2.371657] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 2.375283] sit: IPv6 over IPv4 tunneling driver[ 2.381610] ip6_gre: GRE over IPv6 tunneling driver[ 2.385674] NET: Registered protocol family 17[ 2.389717] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.[ 2.394213] Bridge firewalling registered[ 2.407151] Ebtables v2.0 registered[ 2.411048] Bluetooth: RFCOMM TTY layer initialized[ 2.414490] Bluetooth: RFCOMM socket layer initialized[ 2.419133] Bluetooth: RFCOMM ver 1.11[ 2.424303] Bluetooth: BNEP (Ethernet Emulation) ver 1.3[ 2.428059] Bluetooth: BNEP filters: protocol multicast[ 2.433501] Bluetooth: BNEP socket layer initialized[ 2.438515] l2tp_core: L2TP core driver, V2.0[ 2.443660] l2tp_netlink: L2TP netlink interface[ 2.447965] 8021q: 802.1Q VLAN Support v1.8[ 2.453426] Registering SWP/SWPB emulation handler[ 2.458753] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 2.462863] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 2.468765] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0[ 2.475862] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2[ 2.482479] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0[ 2.490135] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable[ 2.497649] cpr3_mem_acc_init: apc: not using memory accelerator regulator[ 2.506780] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 675000 uV[ 2.513715] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 787500 uV[ 2.523713] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 850000 uV[ 2.533518] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 900000 uV[ 2.543368] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 588, quot_offset[ 7]= 0[ 2.553141] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 784, quot_offset[ 7]= 195[ 2.563991] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]= 885, quot_offset[ 7]= 100[ 2.574927] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]= 958, quot_offset[ 7]= 70[ 2.586130] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop[ 2.598491] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz[ 2.604223] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 864000 KHz[ 2.612079] ubi0: attaching mtd17[ 2.689814] random: nonblocking pool is initialized[ 2.907448] ubi0: scanning is finished[ 2.912439] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 33, need 39[ 2.912834] ubi0: attached mtd17 (name “alt_rootfs”, size 74 MiB)[ 2.921676] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 2.927926] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 2.934688] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096[ 2.941553] ubi0: good PEBs: 591, bad PEBs: 1, corrupted PEBs: 0[ 2.948322] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128[ 2.954569] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1534575391[ 2.961609] ubi0: available PEBs: 0, total reserved PEBs: 591, PEBs reserved for bad PEB handling: 33[ 2.970905] ubi0: background thread “ubi_bgt0d” started, PID 134[ 2.980868] input: soc:gpio_keys as /devices/platform/soc/soc:gpio_keys/input/input0[ 2.986175] hctosys: unable to open rtc device (rtc0)[ 3.002299] VFS: Mounted root (squashfs filesystem) readonly on device 31:20.[ 3.003477] Freeing unused kernel memory: 1024K (80b00000 - 80c00000)*
_ _ __ _ __ _____ __ __ _____ | | | || \ | | / // ____]\ \ / // ____]TM | | | || \ | | / /| (___ \ V /| (____ | | | || |\ \| |\ \ \____ \ \ / \____ \ | |_____ | || | \ | \ \ ____) | | | ____) | |_______||_||_| \__| \_\[____ / |_| [_____/
© 2013 Belkin International, Inc. and/or its affiliates. All rights reserved. Booting elise (firmware version 1.1.7.209317) *[utopia][init] System Initialization[utopia][init] Creating /proc[utopia][init] Creating /sys[utopia][init] Creating /dev[utopia][init] Creating /tmp[utopia][init] Allocating 60M for /tmp[utopia][init] Prepairing /dev/pts[utopia][init] Setting /tmp and /var permissions[utopia][init] Starting udev..Attempting mount of ubifs syscfg partitionUBI device number 1, total 544 LEBs (69074944 bytes, 65.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)[utopia][init] Using persistent syscfg data from /var/config/syscfg[utopia][init] Starting system logging[utopia][init] Starting sysevent subsystem[utopia][init] Starting blue ...[utopia][init] Checking HW version...XB[utopia][init] Enabling DesignWare USB3 DRD Core drivers[utopia][init] Loading QCA Ethernet, NSS and GMAC driversnet.netfilter.nf_conntrack_acct = 1[utopia][init] Late loading usb driversmodprobe: module nls_utf8 not found in modules.dep[utopia][init] Setting any unset system values to default[utopia][init] no persistence config file (/var/config/pstcfg) foundsetting up MAC addresses for all interface based on E8:9F:80:7B:B6:FBUpdating NTP Servers if necessary[utopia][init] syscfg loaded removing tmp file SSDK Init OK!operation done. SSDK Init OK![Ethernet Type]:0x0operation done. SSDK Init OK!operation done. SSDK Init OK!operation done.checking for interactive script start up...no user scheduled tasks found...senq running /etc/init.d/service_senq.sh Starting in mode 01970-01-01 00:00:09: node-mode running Good block at 0x00000000Updating BootCount Page[21]:A800 ... Done[utopia][init] LAN Ports LED settingsattempting to sync sysinfo.cgi auth credentials[utopia][init] Loading Buttons drivers[utopia][init] Setup link to WiFi firmware and board data (US)[utopia][init] Multi-region is not supported or not enabled[utopia][init] Cert region: US[utopia][init] No REGION definded, use FCC[utopia][init] Load WiFi cal data from MTD(mtd8) to FS.65536+0 records in65536+0 records out65536 bytes (64.0KB) copied, 0.236214 seconds, 270.9KB/s[utopia][init] Loading WLAN drivers/bin/sh: can't open '/etc/rc.common'[utopia][init] Loading QCA Enhanced Connection managernet.bridge.bridge-nf-call-ip6tables = 1net.bridge.bridge-nf-call-iptables = 1dev.nss.general.redirect = 1[utopia][init] Initializing BTLE interface[utopia][init] Bluetooth Mac Address: E8 9F 80 7B B6 FB[utopia][init] Cert Region: US[utopia][init] BT PSR: /etc/pb-234-csr8x11-rev2.psrLoading PSKEY_HCI_LMP_LOCAL_VERSION ... doneLoading PSKEY_LMP_REMOTE_VERSION ... doneLoading 0x212c ... doneLoading 0x212d ... doneLoading 0x212e ... doneLoading 0x212f ... doneLoading 0x2130 ... doneLoading 0x2131 ... doneLoading 0x2132 ... doneLoading 0x2133 ... doneLoading 0x2134 ... doneLoading 0x2135 ... doneLoading 0x2136 ... doneLoading 0x2137 ... doneLoading 0x220b ... doneLoading 0x222b ... doneLoading 0x222c ... doneLoading 0x2139 ... doneLoading 0x213a ... doneLoading 0x213b ... doneLoading PSKEY_LC_MAX_TX_POWER ... doneLoading PSKEY_HOST_INTERFACE ... doneLoading 0x01ea ... doneLoading PSKEY_ANA_FREQ ... doneLoading PSKEY_ANA_FTRIM ... doneLoading 0x22c8 ... doneDevice setup complete[utopia][init] BTLE interface ready to useinserting fpbypass.ko for QCAattempting to sync sysinfo.cgi auth credentialsadding group for lldpd userThu Oct 11 06:00:00 UTC 2012Starting devicedb ... (none) login: wan, sysevent received: wan-startDeviceDB database version 3Options:
Daemonize : yes Server UDS Path : /tmp/devicedb/server_link Database File : /tmp/devicedb/devicedb.db DB Transient File : /tmp/devicedb/transient.db
DeviceDB Daily Backup Cron job createdNo TopoDB persistence data to importTopoDB data not importedlldpd event lan_ipaddr 192.168.1.1 received. killall: lldpd: no process killedping6: sendto: Network is unreachablelldpd event lldpd-start received. lldpd configuration already runningARP agent not started: not in master mode.Starting ddd_ethernet_agent ... setting root_accessible to 0 by defaultmosquitto aborting: not Masterlldp updating callback scriptsservice_guardian.sh is called with lan-statusEntry tsmb lan-status, 1lldpd event lldp::root_accessible 0 received. nss_build_bypass is called with lan-startedLighttpd Model Base: MR73Generating Rainier lighttpd configBuild temporary www configuration directory: TSLIIHauhEfGEping6: sendto: Network is unreachableconntrack_parse running creating conntrack cron jobARP agent not started: not in master mode.Power cycle Ethernet ports.RTNETLINK answers: Device or resource busylldpd event ETH::port_1_status down received. Registering Service myrouter._http._tcp.local port 80lldpd event ETH::port_2_status down received. wifi, sysevent received: lan-started (Wed Oct 10 23:00:08 PDT 2012)wifi, service_start()Got a reply for myrouter._http._tcp.local.: Name now registered and active[utopia][init] Loading GMAC and WLAN drivers[utopia][init] Creating wifi devices Multi-region is not supported or not enabledmosquitto aborting: not Master[utopia] Not setting ppp_clamp_mtuEntry tsmb lan-status, 1service_guardian.sh is called with lan-statuslldpd event ETH::port_3_status down received. smart connect client, generating client device datalldpd event ETH::port_4_status down received. lldpd event ETH::port_5_status down received. backhaul_switching status event system_state-normal receivedping6: sendto: Network is unreachablewifi, wifi_physical_start(ath0)backhaul_switching status event backhaul::media 0 received on backhaul_switching_mgrwifi, wl0_state=down, do not start physical ath0wifi, wifi_virtual_start(ath0)Backhaul media 0 received, but wifi status is not started. Will do backhaul check laterwifi, wl0_state=down, do not start virtual ath0wifi, wifi_physical_start(ath1)wifi, wl1_state=down, do not start physical ath1wifi, wifi_virtual_start(ath1)wifi, wl1_state=down, do not start virtual ath1wifi, start_hostapd()BusyBox v1.19.4 (2021-12-03 16:56:05 PST) multi-call binary.Usage: grep [-HhnlLoqvsriwFE] [-m N] [-A/B/C N] PATTERN/-e PATTERN.../-f FILE [FILE]...Search for PATTERN in FILEs (or stdin)
HAdd 'filename:' prefix
hDo not add 'filename:' prefix
nAdd 'line_no:' prefix
lShow only names of files that match
LShow only names of files that don't match
cShow only count of matching lines
oShow only the matching part of line
qQuiet. Return 0 if PATTERN is found, 1 otherwise
vSelect non-matching lines
sSuppress open and read errors
rRecurse
iIgnore case
wMatch whole words only
FPATTERN is a literal (not regexp)
EPATTERN is an extended regexp
m NMatch up to N times per file
A NPrint N lines of trailing context
B NPrint N lines of leading context
C NSame as '-A N -B N'
e PTRNPattern to match
f FILERead pattern from file
start mcsd succeeded (Wed Oct 10 23:00:16 PDT 2012)23.00.16.434154 MCSD plugin info : Initializing plugin managerath0 no private ioctls.ath0 no transmit-power information.ath0 no transmit-power information.ath1 no transmit-power information.ath1 no transmit-power information.Not ready for JNAP. Sleeping for 15 seconds...configurator: got event(guardian-configured, )nss_build_bypass is called with guardian-configuredkillall: mdns_lookup: no process killedEntry tsmb tsmb-stop, 1LookUpMaster call OK.mDNS lookup is on going...smart_connect, sysevent received: wifi-status starting2012-10-11 06:00:26: Setting defaults[utopia] Not setting ppp_clamp_mtu on dslite protocolnss_build_bypass is called with ipv4_wan_ipaddrlldpd event ipv4_wan_ipaddr 0.0.0.0 received. fastpath, sysevent received: qos_enabledgetting geoip information for 0.0.0.0
% Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed
0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (6) Could not resolve: freegeoip.net (Could not contact DNS servers)
net.bridge.bridge-nf-call-ip6tables = 1net.bridge.bridge-nf-call-iptables = 1dev.nss.general.redirect = 1nss_build_bypass is called with build_bypasswan, sysevent received: phylink_wan_stateRestarting nfqrecv service...btsetup servicebtsetup: smart_connect::setup_statusstate_machine entering READYconfigurator: got event(firewall-status, starting)btsetup: Unconfigured mode and Peripheral rolepub_devinfo_status: Error: could not determine HOST_ADDRbluetoothd.init: /var/run/dbus createdbluetoothd.init: dbus-daemon started==⇒ RESET ELISE usb powerpub_wlan_status: Error: could not determine HOST_ADDRsmart_connect, sysevent received: wifi-status startedconfigurator: got event(firewall-status, started)hcisetup: Enabled LE advertisingbtsetup[0] succeeded.configurator: got event(wan-status, starting)configurator: got event(firewall-status, starting)configurator: got event(firewall-status, started)Got a TERM signal, will terminate.Warning! nfqrecv encountered errors when doing recv(): Interrupted system callkillall: nfqrecv: no process killedsubscriber running /etc/init.d/service_subscriber.sh subscriber-stop NULL MODE: 0killall: omsgd: no process killedkillall: configure_me_monitor.sh: no process killedrm: can't remove '/var/run/configure_me_monitor.sh.pid': No such file or directoryconfigurator: got event(firewall-status, starting)configurator: got event(firewall-status, started)configurator: got event(firewall-status, starting)configurator: got event(nfqrecv-status, stopped)configurator: got event(firewall-status, started)configurator: got event(nfqrecv-status, started)configurator: got event(firewall-status, starting)configurator: got event(firewall-status, started)Entry tsmb tsmb-stop, 1Entry tsmb tsmb-start, 1[fw.sh] fwup_checked_after_boot: 0[fwupd] status details:“ERROR: Connecting server”[fw.sh] fwup_forced_update: 0
OEM bootlog v1.1.4
Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2S - IMAGE_VARIANT_STRING=IPQ6018LAS - OEM_IMAGE_VERSION_STRING=crm-ubuntu64S - Boot Interface: NANDS - Secure Boot: OffS - Boot Config @ 0x000a602c = 0x000002e5S - JTAG ID @ 0x000a607c = 0x001390e1S - OEM ID @ 0x000a6080 = 0x00000000S - Serial Number @ 0x000a4128 = 0x0642ed00S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009S - PBL Patch Ver: 1S - I-cache: OnS - D-cache: OnB - 3413 - PBL, StartB - 592 - bootable_media_detect_entry, StartB - 4339 - bootable_media_detect_success, StartB - 5147 - elf_loader_entry, StartB - 5319 - auth_hash_seg_entry, StartB - 7786 - auth_hash_seg_exit, StartB - 8281 - elf_segs_hash_verify_entry, StartB - 110429 - elf_segs_hash_verify_exit, StartB - 114855 - auth_xbl_sec_hash_seg_entry, StartB - 114998 - auth_xbl_sec_hash_seg_exit, StartB - 121553 - xbl_sec_segs_hash_verify_entry, StartB - 121553 - xbl_sec_segs_hash_verify_exit, StartB - 122483 - PBL, EndB - 103242 - SBL1, StartB - 243359 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4B - 245799 - clock_init, StartD - 2836 - clock_init, DeltaB - 254370 - boot_flash_init, StartD - 26199 - boot_flash_init, DeltaB - 283741 - sbl1_ddr_set_default_params, StartD - 244 - sbl1_ddr_set_default_params, DeltaB - 290360 - boot_config_data_table_init, StartD - 4727 - boot_config_data_table_init, Delta - (575 Bytes)B - 300211 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0B - 305061 - Image Load, StartD - 6619 - OEM_MISC Image Loaded, Delta - (0 Bytes)B - 314394 - Image Load, StartD - 5063 - PMIC Image Loaded, Delta - (0 Bytes)B - 322263 - sbl1_ddr_set_params, StartB - 327234 - CPR configuration: 0x366B - 330437 - Pre_DDR_clock_init, StartD - 183 - Pre_DDR_clock_init, DeltaD - 0 - sbl1_ddr_set_params, DeltaB - 367006 - Image Load, StartD - 427 - APDP Image Loaded, Delta - (0 Bytes)B - 380121 - Image Load, StartD - 457 - QTI_MISC Image Loaded, Delta - (0 Bytes)B - 382531 - Image Load, StartD - 884 - Auth MetadataD - 640 - Segments hash checkD - 22234 - QSEE Dev Config Image Loaded, Delta - (36354 Bytes)B - 406748 - Image Load, StartD - 6466 - Auth MetadataD - 10675 - Segments hash checkD - 329339 - QSEE Image Loaded, Delta - (1470632 Bytes)B - 736483 - Image Load, StartD - 702 - Auth MetadataD - 1007 - Segments hash checkD - 34618 - RPM Image Loaded, Delta - (102664 Bytes)B - 772778 - Image Load, StartD - 701 - Auth MetadataD - 3203 - Segments hash checkD - 118798 - APPSBL Image Loaded, Delta - (561320 Bytes)B - 907222 - SBL1, EndD - 804285 - SBL1, DeltaS - Flash Throughput, 5000 KB/s (2171545 Bytes, 422476 us)S - Core 0 Frequency, 800 MHzS - DDR Frequency, 466 MHz
U-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800)
CBT U-Boot ver: 2.3.01 ([IPQ6018].[SPF11.CSU1].[code version])
DRAM: smem ram ptable found: ver: 2 len: 4512 MiBNAND: ONFI device foundID = 1590aac2Vendor = c2Device = aaSF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)256 MiBMMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device treeIn: serial@78B1000Out: serial@78B1000Err: serial@78B1000machid: 8030200eth0 MAC Address from ART is not valideth1 MAC Address from ART is not valideth2 MAC Address from ART is not valideth3 MAC Address from ART is not valideth4 MAC Address from ART is not valideth5 MAC Address from ART is not valid
Updating boot_count ... done
Hit any key to stop autoboot: 0 Setting bus to 0Valid chip addresses: 62
NAND read: device 0 offset 0x6680000, size 0x800000 8388608 bytes read: OK## Loading kernel from FIT Image at 44000000 ...
Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM Linksys Linux-4.4.60 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e4 Data Size: 4577078 Bytes = 4.4 MiB Architecture: ARM OS: Linux Load Address: 0x41208000 Entry Point: 0x41208000 Hash algo: crc32 Hash value: c0741528 Hash algo: sha1 Hash value: 2dd7feb32fffa84b958eb19b8d34ecf0c9e12777 Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM Linksys Elise device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x4445d94c Data Size: 67045 Bytes = 65.5 KiB Architecture: ARM Hash algo: crc32 Hash value: 3b3f4af7 Hash algo: sha1 Hash value: 80960d4647a74007b900e699633a4870647d4d53 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x4445d94c Uncompressing Kernel Image ... OK Loading Device Tree to 484ec000, end 484ff5e4 ... OK
Could not find PCI in device treeUsing machid 0x8030200 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0[ 0.000000] Initializing cgroup subsys cpuset[ 0.000000] Initializing cgroup subsys cpu[ 0.000000] Initializing cgroup subsys cpuacct[ 0.000000] Linux version 4.4.60 (root@build-vm) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r35193) ) #1 SMP PREEMPT Fri Jul 24 14:01:17 PDT 2020[ 0.000000] CPU: ARMv7 Processor [51af8014] revision 4 (ARMv7), cr=10c0383d[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache[ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ6018/AP-CP03-C1[ 0.000000] Ignoring memory range 0x40000000 - 0x41000000[ 0.000000] Memory policy: Data cache writealloc[ 0.000000] psci: probing for conduit method from DT.[ 0.000000] psci: PSCIv1.0 detected in firmware.[ 0.000000] psci: Using standard PSCI v0.2 function IDs[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.[ 0.000000] PERCPU: Embedded 11 pages/cpu @9eb3f000 s15424 r8192 d21440 u45056[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 110244[ 0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait swiotlb=1 clk_ignore_unused coherent_pool=2M[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)[ 0.000000] Memory: 431092K/445440K available (6330K kernel code, 450K rwdata, 2096K rodata, 268K init, 358K bss, 14348K reserved, 0K cma-reserved, 0K highmem)[ 0.000000] Virtual kernel memory layout:[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)[ 0.000000] vmalloc : 0x9f800000 - 0xff800000 (1536 MB)[ 0.000000] lowmem : 0x80000000 - 0x9f000000 ( 496 MB)[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)[ 0.000000] .text : 0x80208000 - 0x80a42d00 (8428 kB)[ 0.000000] .init : 0x80a43000 - 0x80a86000 ( 268 kB)[ 0.000000] .data : 0x80a86000 - 0x80af6b5c ( 451 kB)[ 0.000000] .bss : 0x80af9000 - 0x80b52b98 ( 359 kB)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1[ 0.000000] Preemptible hierarchical RCU implementation.[ 0.000000] Build-time adjustment of leaf fanout to 32.[ 0.000000] NR_IRQS:16 nr_irqs:16 16[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns[ 0.000016] Switching to timer-based delay loop, resolution 41ns[ 0.000666] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)[ 0.000679] pid_max: default: 32768 minimum: 301[ 0.000769] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.000778] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.001301] Initializing cgroup subsys io[ 0.001316] Initializing cgroup subsys memory[ 0.001338] Initializing cgroup subsys devices[ 0.001353] Initializing cgroup subsys freezer[ 0.001362] Initializing cgroup subsys net_cls[ 0.001371] Initializing cgroup subsys pids[ 0.001393] CPU: Testing write buffer coherency: ok[ 0.001762] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000[ 0.001808] Setting up static identity map for 0x41208280 - 0x412082d8[ 0.090257] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001[ 0.120238] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002[ 0.150274] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003[ 0.150328] Brought up 4 CPUs[ 0.150350] SMP: Total of 4 processors activated (192.00 BogoMIPS).[ 0.150356] CPU: All CPU(s) started in SVC mode.[ 0.168602] VFP support v0.3: implementor 51 architecture 3 part 40 variant 3 rev 4[ 0.168891] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns[ 0.168914] futex hash table entries: 1024 (order: 4, 65536 bytes)[ 0.169276] pinctrl core: initialized pinctrl subsystem[ 0.170314] NET: Registered protocol family 16[ 0.171434] DMA: preallocated 2048 KiB pool for atomic coherent allocations[ 0.200113] cpuidle: using governor ladder[ 0.230131] cpuidle: using governor menu[ 0.244184] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.256257] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.[ 0.256267] hw-breakpoint: maximum watchpoint size is 8 bytes.[ 0.257781] CPU: IPQ6018, SoC Version: 1.0[ 0.257995] <CORE> glink_init: IPC Logging Disabled[ 0.258283] <CORE> glink_core_register_transport: IPC Logging disabled[ 0.258352] msm_glink_smem_native_xprtrx fifo not found[ 0.258653] <CORE> glink_core_register_transport: IPC Logging disabled[ 0.258693] glink_core_link_up glink is up[ 0.258982] msm_rpm_dev_probe: APSS-RPM communication over GLINK[ 0.259059] msm_rpm_trans_notify_state: glink config params: transport=(null), edge=rpm, name=rpm_requests[ 0.259947] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 0.262084] IPC logging disabled[ 0.262090] IPC logging disabled[ 0.262096] IPC logging disabled[ 0.262100] IPC logging disabled[ 0.262105] IPC logging disabled[ 0.262311] sps:sps is ready.[ 0.291807] usbcore: registered new interface driver usbfs[ 0.291866] usbcore: registered new interface driver hub[ 0.291935] usbcore: registered new device driver usb[ 0.292003] pps_core: LinuxPPS API ver. 1 registered[ 0.292010] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it[ 0.292035] PTP clock support registered[ 0.293944] Bluetooth: Core ver 2.21[ 0.293975] NET: Registered protocol family 31[ 0.293981] Bluetooth: HCI device and connection manager initialized[ 0.293994] Bluetooth: HCI socket layer initialized[ 0.294004] Bluetooth: L2CAP socket layer initialized[ 0.294027] Bluetooth: SCO socket layer initialized[ 0.294310] clocksource: Switched to clocksource arch_sys_counter[ 0.297210] NET: Registered protocol family 2[ 0.297770] TCP established hash table entries: 4096 (order: 2, 16384 bytes)[ 0.297819] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)[ 0.297894] TCP: Hash tables configured (established 4096 bind 4096)[ 0.297931] UDP hash table entries: 256 (order: 1, 8192 bytes)[ 0.297953] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)[ 0.298107] NET: Registered protocol family 1[ 0.299166] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available[ 0.307755] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.307776] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.[ 0.311630] Key type asymmetric registered[ 0.311645] Asymmetric key parser 'x509' registered[ 0.311683] io scheduler noop registered[ 0.311696] io scheduler deadline registered (default)[ 0.320477] NET: Registered protocol family 27[ 0.320488] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled[ 0.320505] qmi_log_init: IPC Logging disabled[ 0.320511] qmi_log_init: IPC Logging disabled[ 0.320647] msm_rpm_log_probe: OK[ 0.320960] msm-dcc b3000.dcc: DCC XPU is not specified[ 0.321185] msm-dcc b3000.dcc: DCC REG dump setup failed[ 0.321197] msm-dcc b3000.dcc: DCC SRAM dump setup failed[ 0.321221] msm-dcc b3000.dcc: jiffies_64: 0xffff8aef, cntvct_64: 0x6794734[ 0.321232] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0x9fa7e004)[ 0.321242] msm-dcc b3000.dcc: gcnt_lo: 0x06794953(0x9fa7e000)[ 0.321810] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set[ 0.322591] msm_serial 78b0000.serial: msm_serial: detected port #1[ 0.322627] msm_serial 78b0000.serial: uartclk = 24000000[ 0.322658] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 20, base_baud = 1500000) is a MSM[ 0.322972] msm_serial 78b1000.serial: msm_serial: detected port #0[ 0.322999] msm_serial 78b1000.serial: uartclk = 1843200[ 0.323024] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 21, base_baud = 115200) is a MSM[ 0.323039] msm_serial: console setup on port #0[ 1.080871] console [ttyMSM0] enabled[ 1.085902] msm_serial: driver initialized[ 1.089398] msm_serial_hsl_init: driver initialized[ 1.102661] brd: module loaded[ 1.103302] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64[ 1.106301] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00, 0, 0[ 1.112764] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa[ 1.118200] nand: ONFI 10-Compliant Macronix MX30UF2G18AC[ 1.124706] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64[ 1.130044] 20 ofpart partitions found on MTD device qcom_nand.0[ 1.137433] Creating 20 MTD partitions on “qcom_nand.0”:[ 1.143583] 0x000000000000-0x000000180000 : “0:SBL1”[ 1.150915] 0x000000180000-0x000000280000 : “0:MIBIB”[ 1.155420] 0x000000280000-0x000000600000 : “0:QSEE”[ 1.162236] 0x000000600000-0x000000680000 : “0:DEVCFG”[ 1.165056] 0x000000680000-0x000000700000 : “0:RPM”[ 1.169883] 0x000000700000-0x000000780000 : “0:CDT”[ 1.174668] 0x000000780000-0x000000800000 : “0:APPSBLENV”[ 1.179539] 0x000000800000-0x000000980000 : “0:APPSBL”[ 1.185862] 0x000000980000-0x000000a00000 : “0:ART”[ 1.190167] 0x000000a00000-0x000001300000 : “0:WIFIFW”[ 1.201095] 0x000001300000-0x000001380000 : “0:ETHPHYFW”[ 1.202354] 0x000001380000-0x000001400000 : “u_env”[ 1.206707] 0x000001400000-0x000001440000 : “s_env”[ 1.211054] 0x000001440000-0x000001480000 : “devinfo”[ 1.215879] 0x000001480000-0x000006680000 : “kernel”[ 1.282206] 0x000001c80000-0x000006680000 : “rootfs”[ 1.337997] mtd: device 15 (rootfs) set to be root filesystem[ 1.338257] mtdsplit: no squashfs found in “rootfs”[ 1.342722] 0x000006680000-0x00000b880000 : “alt_kernel”[ 1.409127] 0x000006e80000-0x00000b880000 : “alt_rootfs”[ 1.465306] 0x00000b880000-0x00000ba80000 : “sysdiag”[ 1.467653] 0x00000ba80000-0x00000fe80000 : “syscfg”[ 1.521213] libphy: Fixed MDIO Bus: probed[ 1.741980] qca-mdio 90000.mdio: Could not find phy-reset-gpio[ 1.742128] libphy: qca_mdio: probed[ 1.747949] qca-mdio 90000.mdio: qca-mdio driver was registered[ 1.750561] Unable to create IPC log context![ 1.756510] cnss: Platform driver probed successfully.[ 1.761043] dummy_hcd dummy_hcd.0: USB Host+Gadget Emulator, driver 02 May 2005[ 1.765665] dummy_hcd dummy_hcd.0: Dummy host controller[ 1.772829] dummy_hcd dummy_hcd.0: new USB bus registered, assigned bus number 1[ 1.779023] hub 1-0:1.0: USB hub found[ 1.785810] hub 1-0:1.0: 1 port detected[ 1.789953] i2c /dev entries driver[ 1.799328] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com[ 1.799368] Bluetooth: HCI UART driver ver 2.3[ 1.806848] Bluetooth: HCI UART protocol H4 registered[ 1.811076] Bluetooth: HCI UART protocol BCSP registered[ 1.816213] Bluetooth: HCI UART protocol ATH3K registered[ 1.822091] sdhci: Secure Digital Host Controller Interface driver[ 1.826980] sdhci: Copyright© Pierre Ossman[ 1.833044] sdhci-pltfm: SDHCI platform and OF driver helper[ 1.838438] leds-pca963x 0-0062: PCA963X_HW_BLINK ON[ 1.845801] [ 1.845801] Version Rollback Feature Disabled[ 1.848726] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x08b04000[ 1.853793] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x08b04000[ 1.869688] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x08b04000[ 1.884172] sps:BAM 0x08b04000 is registered.[ 1.891427] DEV CI test message[ 1.895566] remoteproc remoteproc0: q6v5-wcss is available[ 1.898433] subsys-restart: ssr_parse_restart_orders(): q6v5_m3 device has been added to q6v5-m3's restart group[ 1.903544] subsys-restart: ssr_parse_restart_orders(): q6v5_wcss device has been added to q6v5-m3's restart group[ 1.913979] remoteproc remoteproc1: q6v5-m3 is available[ 1.924615] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000[ 1.929577] coresight-csr 6001000.csr: CSR initialized[ 1.937031] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000[ 1.942004] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000[ 1.949566] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000[ 1.956944] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000[ 1.964318] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000[ 1.971689] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000[ 1.979078] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000[ 1.986470] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000[ 1.993822] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000[ 2.001227] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000[ 2.008592] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000[ 2.015954] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000[ 2.023315] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000[ 2.030706] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000[ 2.038091] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000[ 2.045555] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000[ 2.052839] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000[ 2.060348] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000[ 2.067727] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000[ 2.075135] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000[ 2.082545] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000[ 2.089903] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06064000[ 2.096952] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06064000[ 2.112643] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06064000[ 2.127151] sps:BAM 0x06064000 is registered.[ 2.133826] coresight-tmc 6048000.tmc: TMC REG dump setup failed. ret: -38[ 2.138109] coresight-tmc 6048000.tmc: TMC initialized[ 2.144922] coresight-tmc 6047000.tmc: TMC ETF-ETB dump setup failed. ret: -38[ 2.149889] coresight-tmc 6047000.tmc: TMC REG dump setup failed. ret: -38[ 2.157353] coresight-tmc 6047000.tmc: TMC initialized[ 2.164321] coresight-funnel 6041000.funnel: FUNNEL initialized[ 2.169306] coresight-funnel 6100000.funnel: FUNNEL initialized[ 2.175134] coresight-funnel 6130000.funnel: FUNNEL initialized[ 2.181032] coresight-funnel 6120000.funnel: FUNNEL initialized[ 2.186955] coresight-funnel 61a1000.funnel: FUNNEL initialized[ 2.193092] coresight-etm4x 619c000.etm: ETM REG dump setup failed. ret -38[ 2.198956] coresight-etm4x 619c000.etm: ETM 4.0 initialized[ 2.205698] coresight-etm4x 619d000.etm: ETM REG dump setup failed. ret -38[ 2.211788] coresight-etm4x 619d000.etm: ETM 4.0 initialized[ 2.218328] coresight-etm4x 619e000.etm: ETM REG dump setup failed. ret -38[ 2.224393] coresight-etm4x 619e000.etm: ETM 4.0 initialized[ 2.230925] coresight-etm4x 619f000.etm: ETM REG dump setup failed. ret -38[ 2.236990] coresight-etm4x 619f000.etm: ETM 4.0 initialized[ 2.243483] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized[ 2.249529] coresight-stm 6002000.stm: STM initialized[ 2.258185] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000[ 2.261900] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized[ 2.269940] u32 classifier[ 2.277058] input device check on[ 2.279562] Actions configured[ 2.283330] Netfilter messages via NETLINK v0.30.[ 2.286682] nf_conntrack version 0.5.0 (6735 buckets, 26940 max)[ 2.291889] nf_conntrack_rtsp v0.7 loading[ 2.297527] nf_tables: © 2007-2009 Patrick McHardy kaber@trash.net[ 2.301379] nf_tables_compat: © 2012 Pablo Neira Ayuso pablo@netfilter.org[ 2.308226] xt_time: kernel timezone is -0000[ 2.315092] ip_set: protocol 6[ 2.319689] gre: GRE over IPv4 demultiplexor driver[ 2.322453] ip_gre: GRE over IPv4 tunneling driver[ 2.328322] nf_nat_rtsp v0.7 loading[ 2.332190] ip_tables: (C) 2000-2006 Netfilter Core Team[ 2.336023] arp_tables: (C) 2002 David S. Miller[ 2.341855] NET: Registered protocol family 10[ 2.346718] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 2.350263] sit: IPv6 over IPv4 tunneling driver[ 2.356658] ip6_gre: GRE over IPv6 tunneling driver[ 2.360716] NET: Registered protocol family 17[ 2.364779] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.[ 2.369280] Bridge firewalling registered[ 2.382215] Ebtables v2.0 registered[ 2.386152] Bluetooth: RFCOMM TTY layer initialized[ 2.389554] Bluetooth: RFCOMM socket layer initialized[ 2.394165] Bluetooth: RFCOMM ver 1.11[ 2.399407] Bluetooth: BNEP (Ethernet Emulation) ver 1.3[ 2.403091] Bluetooth: BNEP filters: protocol multicast[ 2.408604] Bluetooth: BNEP socket layer initialized[ 2.413537] l2tp_core: L2TP core driver, V2.0[ 2.418752] l2tp_netlink: L2TP netlink interface[ 2.422998] 8021q: 802.1Q VLAN Support v1.8[ 2.428474] Registering SWP/SWPB emulation handler[ 2.433612] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 2.436682] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0[ 2.443634] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2[ 2.450249] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0[ 2.457908] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable[ 2.465420] cpr3_mem_acc_init: apc: not using memory accelerator regulator[ 2.474552] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 675000 uV[ 2.481486] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 787500 uV[ 2.491481] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 862500 uV[ 2.501291] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 937500 uV[ 2.511136] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 530, quot_offset[ 7]= 0[ 2.520914] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 717, quot_offset[ 7]= 185[ 2.531763] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]= 833, quot_offset[ 7]= 115[ 2.542700] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]= 942, quot_offset[ 7]= 105[ 2.553892] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop[ 2.566262] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz[ 2.571997] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 864000 KHz[ 2.579306] ubi0: attaching mtd17[ 2.659960] random: nonblocking pool is initialized[ 2.884752] ubi0: scanning is finished[ 2.890010] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 34, need 40[ 2.890500] ubi0: attached mtd17 (name “alt_rootfs”, size 74 MiB)[ 2.899251] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 2.905498] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 2.912260] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096[ 2.919125] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0[ 2.925894] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128[ 2.932141] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1088489430[ 2.939183] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 34[ 2.948484] ubi0: background thread “ubi_bgt0d” started, PID 134[ 2.957994] hctosys: unable to open rtc device (rtc0)[ 2.970233] clk: Not disabling unused clocks[ 2.972532] VFS: Mounted root (squashfs filesystem) readonly on device 31:20.[ 2.973781] Freeing unused kernel memory: 268K (80a43000 - 80a86000)*
_ _ __ _ __ _____ __ __ _____ | | | || \ | | / // ____]\ \ / // ____]TM | | | || \ | | / /| (___ \ V /| (____ | | | || |\ \| |\ \ \____ \ \ / \____ \ | |_____ | || | \ | \ \ ____) | | | ____) | |_______||_||_| \__| \_\[____ / |_| [_____/
© 2013 Belkin International, Inc. and/or its affiliates. All rights reserved. Booting elise (firmware version 1.1.4.202174) *[utopia][init] System Initialization[utopia][init] Creating /proc[utopia][init] Creating /sys[utopia][init] Creating /dev[utopia][init] Creating /tmp[utopia][init] Allocating 60M for /tmp[utopia][init] Prepairing /dev/pts[utopia][init] Setting /tmp and /var permissions[utopia][init] Starting udev..Attempting mount of ubifs syscfg partitionUBI device number 1, total 544 LEBs (69074944 bytes, 65.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)[utopia][init] Using persistent syscfg data from /var/config/syscfg[utopia][init] Starting system logging[utopia][init] Starting sysevent subsystem[utopia][init] Starting blue ...[utopia][init] Checking HW version...XB[utopia][init] Enabling DesignWare USB3 DRD Core drivers[utopia][init] Loading QCA Ethernet, NSS and GMAC driversnet.netfilter.nf_conntrack_acct = 1[utopia][init] Late loading usb driversmodprobe: module nls_utf8 not found in modules.dep[utopia][init] Setting any unset system values to default[utopia][init] no persistence config file (/var/config/pstcfg) foundsetting up MAC addresses for all interface based on E8:9F:80:77:EE:2BUpdating NTP Servers if necessary[utopia][init] syscfg loaded removing tmp file
SSDK Init OK!operation done.
checking for interactive script start up...no user scheduled tasks found...senq running /etc/init.d/service_senq.sh Starting in mode 01970-01-01 00:00:10: node-mode running Good block at 0x00000000Updating BootCount Page[18]:9000 ... Done
[utopia][init] LAN Ports LED settingsattempting to sync sysinfo.cgi auth credentials[utopia][init] Loading Buttons drivers[utopia][init] Setup link to WiFi firmware and board data (US)[utopia][init] Multi-region is not supported or not enabled[utopia][init] Cert region: US[utopia][init] No REGION definded, use FCC[utopia][init] Load WiFi cal data from MTD(mtd8) to FS.65536+0 records in65536+0 records out65536 bytes (64.0KB) copied, 0.293176 seconds, 218.3KB/s[utopia][init] Loading WLAN drivers[ 16.743779] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done[ 17.770193] glink_core_link_up glink is up[ 17.770401] glink_xprt_open_eventNSS Auto scaling disabled [utopia][init] Loading QCA Enhanced Connection managernet.bridge.bridge-nf-call-ip6tables = 1net.bridge.bridge-nf-call-iptables = 1[utopia][init] Initializing BTLE interface[utopia][init] Bluetooth Mac Address: E8 9F 80 77 EE 2B[utopia][init] Cert Region: US[utopia][init] BT PSR: /etc/pb-234-csr8x11-rev2.psrDevice setup completeLoading PSKEY_HCI_LMP_LOCAL_VERSION ... doneLoading PSKEY_LMP_REMOTE_VERSION ... doneLoading 0x212c ... doneLoading 0x212d ... doneLoading 0x212e ... doneLoading 0x212f ... doneLoading 0x2130 ... doneLoading 0x2131 ... doneLoading 0x2132 ... doneLoading 0x2133 ... doneLoading 0x2134 ... doneLoading 0x2135 ... doneLoading 0x2136 ... doneLoading 0x2137 ... doneLoading 0x220b ... doneLoading 0x222b ... doneLoading 0x222c ... doneLoading 0x2139 ... doneLoading 0x213a ... doneLoading 0x213b ... doneLoading PSKEY_LC_MAX_TX_POWER ... doneLoading PSKEY_HOST_INTERFACE ... doneLoading 0x01ea ... doneLoading PSKEY_ANA_FREQ ... doneLoading PSKEY_ANA_FTRIM ... doneLoading 0x22c8 ... doneinserting fpbypass.ko for QCAattempting to sync sysinfo.cgi auth credentialsadding group for lldpd userThu Oct 11 06:00:00 UTC 2012
(none) login: Starting devicedb ... wan, sysevent received: wan-start
DeviceDB database version 3Options:
Daemonize : yes Server UDS Path : /tmp/devicedb/server_link Database File : /tmp/devicedb/devicedb.db DB Transient File : /tmp/devicedb/transient.db
DeviceDB Daily Backup Cron job createdNo TopoDB persistence data to importTopoDB data not importedlldpd event lan_ipaddr 192.168.1.1 received. killall: lldpd: no process killedARP agent not started: not in master mode.Device setup completelldpd event lldpd-start received. RTNETLINK answers: Device or resource busyStarting ddd_ethernet_agent ... lldpd configuration already runningsetting root_accessible to 0 by default[utopia][init] BTLE interface ready to usemosquitto aborting: not Masterlldp updating callback scriptssubscriber running /etc/init.d/service_subscriber.sh lan-status starting MODE: 0service_guardian.sh is called with lan-status/etc/init.d/service_subscriber.sh lan-status starting: Not Master; ignoring status change (mode: 0)Entry tsmb lan-status, 1
lldpd event lldp::root_accessible 0 received. lldpd event ETH::port_1_status down received. lldpd event ETH::port_2_status down received. lldpd event ETH::port_3_status down received. lldpd event ETH::port_4_status down received. lldpd event ETH::port_5_status down received. nss_build_bypass is called with lan-started[utopia] Not setting ppp_clamp_mtuLighttpd Model Base: MR73Generating Rainier lighttpd configBuild temporary www configuration directory: TSLIIHauhEfGEconntrack_parse running creating conntrack cron jobARP agent not started: not in master mode.Power cycle Ethernet ports.Registering Service myrouter._http._tcp.local port 80Got a reply for myrouter._http._tcp.local.: Name now registered and activewifi, sysevent received: lan-started (Wed Oct 10 23:00:08 PDT 2012)wifi, service_start()[utopia][init] Loading GMAC and WLAN drivers[utopia][init] Creating wifi devices Multi-region is not supported or not enabledmosquitto aborting: not Master/etc/init.d/service_subscriber.sh lan-status started MODE: 0/etc/init.d/service_subscriber.sh lan-status started: Not Master; ignoring status change (mode: 0)service_guardian.sh is called with lan-statusEntry tsmb lan-status, 1backhaul_switching status event backhaul::media 0 received on backhaul_switching_mgrBackhaul media 0 received, but wifi status is not started. Will do backhaul check laterbackhaul_switching status event system_state-normal receivedsmart connect client, generating client device datawifi, wifi_physical_start(ath0)dev.nss.n2hcfg.n2h_high_water_core0 = 8704dev.nss.n2hcfg.extra_pbuf_core0 = 3100000dev.nss.n2hcfg.n2h_high_water_core0 = 30624dev.nss.n2hcfg.n2h_wifi_pool_buf = 8192dev.nss.n2hcfg.n2h_queue_limit_core0 = 256sysctl: error: 'dev.nss.n2hcfg.n2h_queue_limit_core1' is an unknown keyath0 No such device
Auto channelwifi, wifi_virtual_start(ath0)Not ready for JNAP. Sleeping for 15 seconds...wifi, wifi_user_start(ath0)Interface doesn't accept private ioctl...he_mubfee (8BE0): Invalid argumentwifi_user, ath0 TxBF enabledInterface doesn't accept private ioctl...he_mubfee (8BE0): Invalid argumentwifi, primary AP: ath0 is up (Wed Oct 10 23:00:18 PDT 2012)wifi, wifi_guest_start(ath0)wifi, guest ath2 is disabled, do not start wifi guestwifi, smart::mode is unconfigured do not start smart connect setup and config wifiwifi, wifi_physical_start(ath1)dev.nss.n2hcfg.n2h_high_water_core0 = 26528sysctl: short writedev.nss.n2hcfg.n2h_high_water_core0 = 30624dev.nss.n2hcfg.n2h_wifi_pool_buf = 8192dev.nss.n2hcfg.n2h_queue_limit_core0 = 256sysctl: error: 'dev.nss.n2hcfg.n2h_queue_limit_core1' is an unknown keyath1 No such device
List Flushed Following channels are blocked from Channel selection algorithm [52] [56] [60] [64] [100] [104] [108] [112] [116] [120] [124] [128] [132] [136] [140] Auto channelwifi, wifi_virtual_start(ath1)[utopia] Not setting ppp_clamp_mtu on dslite protocolwan, sysevent received: phylink_wan_statewifi, wifi_user_start(ath1)Interface doesn't accept private ioctl...he_mubfee (8BE0): Invalid argumentwifi_user, ath1 TxBF enabledInterface doesn't accept private ioctl...he_mubfee (8BE0): Invalid argumentwifi_user, ath1 MU-MIMO enabledwifi, primary AP: ath1 is up (Wed Oct 10 23:00:23 PDT 2012)wifi, wifi_guest_start(ath1)wifi, guest ath3 is disabled, do not start wifi guestwifi, start_hostapd()wifi, start hostapd (Wed Oct 10 23:00:24 PDT 2012)Configuration file: /tmp/hostapd-ath0.confConfiguration file: /tmp/hostapd-ath1.confrfkill: Cannot open RFKILL control deviceACS: Automatic channel selection started, this may take a bitACS: Offloading to driverrfkill: Cannot open RFKILL control deviceACS: Automatic channel selection started, this may take a bitACS: Offloading to drivernss_build_bypass is called with guardian-configurednss_build_bypass is called with ipv4_wan_ipaddrgetting geoip information for 0.0.0.0
% Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (6) Could not resolve: freegeoip.net (Could not contact DNS servers)
lldpd event ipv4_wan_ipaddr 0.0.0.0 received. nl80211: ACS Results: PCH: 48 SCH: 36 BW: 80 VHT0: 42 VHT1: 0 HW_MODE: 2ath1: ACS-COMPLETED freq=5240 channel=48wpa_driver_nl80211_set_key: ifindex=21 (ath1) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0wpa_driver_nl80211_set_key: ifindex=21 (ath1) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0wpa_driver_nl80211_set_key: ifindex=21 (ath1) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0wpa_driver_nl80211_set_key: ifindex=21 (ath1) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0Using interface ath1 with hwaddr e8:9f:80:77:ee:2d and ssid “_LinksysSetupE2B”wpa_driver_nl80211_set_key: ifindex=21 (ath1) alg=3 addr=0x54d0f670 key_idx=1 set_tx=1 seq_len=0 key_len=16ath1: interface state UNINITIALIZED→ENABLEDath1: AP-ENABLED ath1: IEEE 802.11 driver had channel switch: freq=5240, ht=1, vht_ch=0x0, offset=-1, width=3 (80 MHz), cf1=5210, cf2=0ath1: CTRL-EVENT-CHANNEL-SWITCH freq=5240 ht_enabled=1 ch_offset=-1 ch_width=80 MHz cf1=5210 cf2=0 dfs=0Entry tsmb tsmb-stop, 1nl80211: ACS Results: PCH: 11 SCH: 7 BW: 40 VHT0: 9 VHT1: 0 HW_MODE: 1ath0: ACS-COMPLETED freq=2462 channel=11wpa_driver_nl80211_set_key: ifindex=20 (ath0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0wpa_driver_nl80211_set_key: ifindex=20 (ath0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0wpa_driver_nl80211_set_key: ifindex=20 (ath0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0wpa_driver_nl80211_set_key: ifindex=20 (ath0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0Using interface ath0 with hwaddr e8:9f:80:77:ee:2c and ssid “_LinksysSetupE2B”wpa_driver_nl80211_set_key: ifindex=20 (ath0) alg=3 addr=0x54d0f670 key_idx=1 set_tx=1 seq_len=0 key_len=16ath0: interface state UNINITIALIZED→ENABLEDath0: AP-ENABLED ath0: IEEE 802.11 driver had channel switch: freq=2462, ht=1, vht_ch=0x0, offset=-1, width=2 (40 MHz), cf1=2452, cf2=0ath0: CTRL-EVENT-CHANNEL-SWITCH freq=2462 ht_enabled=1 ch_offset=-1 ch_width=40 MHz cf1=2452 cf2=0 dfs=0killall: mdns_lookup: no process killedLookUpMaster call OK.mDNS lookup is on going...smart_connect, sysevent received: wifi-status startingstart mcsd succeeded (Wed Oct 10 23:00:29 PDT 2012)23.00.30.008398 MCSD plugin info : Initializing plugin managerfastpath, sysevent received: qos_enablednet.bridge.bridge-nf-call-ip6tables = 0net.bridge.bridge-nf-call-iptables = 0Restarting nfqrecv service...btsetup servicebtsetup: smart_connect::setup_statusstate_machine entering READY==⇒ RESET ELISE usb powerbtsetup: Unconfigured mode and Peripheral rolepub_devinfo_status: Error: could not determine HOST_ADDRbluetoothd.init: /var/run/dbus createdbluetoothd.init: dbus-daemon startedpub_wlan_status: Error: could not determine HOST_ADDRhcisetup: Enabled LE advertisingsmart_connect, sysevent received: wifi-status startedGot a TERM signal, will terminate.Warning! nfqrecv encountered errors when doing recv(): Interrupted system callkillall: nfqrecv: no process killedping: bad address 'www.linksys.com'[fw.sh] fwup_checked_after_boot: 0[fwupd] status details:“ERROR: Connecting server”[fw.sh] fwup_forced_update: 0Entry tsmb tsmb-stop, 1Entry tsmb tsmb-start, 1
U-Boot bootlog
Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2S - IMAGE_VARIANT_STRING=IPQ6018LAS - OEM_IMAGE_VERSION_STRING=crm-ubuntu64S - Boot Interface: NANDS - Secure Boot: OffS - Boot Config @ 0x000a602c = 0x000002e5S - JTAG ID @ 0x000a607c = 0x001390e1S - OEM ID @ 0x000a6080 = 0x00000000S - Serial Number @ 0x000a4128 = 0xfe655252S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009S - PBL Patch Ver: 1S - I-cache: OnS - D-cache: OnB - 3413 - PBL, StartB - 592 - bootable_media_detect_entry, StartB - 4339 - bootable_media_detect_success, StartB - 5147 - elf_loader_entry, StartB - 5319 - auth_hash_seg_entry, StartB - 7787 - auth_hash_seg_exit, StartB - 8280 - elf_segs_hash_verify_entry, StartB - 110428 - elf_segs_hash_verify_exit, StartB - 114852 - auth_xbl_sec_hash_seg_entry, StartB - 114995 - auth_xbl_sec_hash_seg_exit, StartB - 121548 - xbl_sec_segs_hash_verify_entry, StartB - 121549 - xbl_sec_segs_hash_verify_exit, StartB - 122478 - PBL, EndB - 103242 - SBL1, StartB - 243329 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4B - 245769 - clock_init, StartD - 2836 - clock_init, DeltaB - 254309 - boot_flash_init, StartD - 26169 - boot_flash_init, DeltaB - 283680 - sbl1_ddr_set_default_params, StartD - 213 - sbl1_ddr_set_default_params, DeltaB - 290299 - boot_config_data_table_init, StartD - 4727 - boot_config_data_table_init, Delta - (575 Bytes)B - 300120 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0B - 305000 - Image Load, StartD - 6619 - OEM_MISC Image Loaded, Delta - (0 Bytes)B - 314333 - Image Load, StartD - 5063 - PMIC Image Loaded, Delta - (0 Bytes)B - 322202 - sbl1_ddr_set_params, StartB - 327173 - CPR configuration: 0x366B - 330376 - Pre_DDR_clock_init, StartD - 183 - Pre_DDR_clock_init, DeltaD - 0 - sbl1_ddr_set_params, DeltaB - 367006 - Image Load, StartD - 458 - APDP Image Loaded, Delta - (0 Bytes)B - 380121 - Image Load, StartD - 427 - QTI_MISC Image Loaded, Delta - (0 Bytes)B - 382561 - Image Load, StartD - 945 - Auth MetadataD - 701 - Segments hash checkD - 22326 - QSEE Dev Config Image Loaded, Delta - (36354 Bytes)B - 406839 - Image Load, StartD - 6527 - Auth MetadataD - 10645 - Segments hash checkD - 329522 - QSEE Image Loaded, Delta - (1470632 Bytes)B - 736788 - Image Load, StartD - 702 - Auth MetadataD - 976 - Segments hash checkD - 34526 - RPM Image Loaded, Delta - (102664 Bytes)B - 772992 - Image Load, StartD - 671 - Auth MetadataD - 3172 - Segments hash checkD - 118828 - APPSBL Image Loaded, Delta - (561320 Bytes)B - 907436 - SBL1, EndD - 804499 - SBL1, DeltaS - Flash Throughput, 5000 KB/s (2171545 Bytes, 422660 us)S - Core 0 Frequency, 800 MHzS - DDR Frequency, 466 MHzU-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800)CBT U-Boot ver: 2.3.01 ([IPQ6018].[SPF11.CSU1].[code version])DRAM: smem ram ptable found: ver: 2 len: 4512 MiBNAND: ONFI device foundID = 1590aac2Vendor = c2Device = aaSF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)256 MiBMMC: sdhci: Node Not found, skipping initializationPCI0 is not defined in the device treeIn: serial@78B1000Out: serial@78B1000Err: serial@78B1000machid: 8030200eth0 MAC Address from ART is not valideth1 MAC Address from ART is not valideth2 MAC Address from ART is not valideth3 MAC Address from ART is not valideth4 MAC Address from ART is not valideth5 MAC Address from ART is not validUpdating boot_count ... doneHit any key to stop autoboot: 1 0 Net: MAC0 addr:0:3:7f:ba:db:adPHY ID1: 0x4dPHY ID2: 0xd0b1EDMA ver 1 hw initNum rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)RxDesc:1 (15-15) RxFill:1 (7-7)ipq6018_edma_alloc_rings: successfullipq6018_edma_setup_ring_resources: successfullipq6018_edma_configure_rings: successfullipq6018_edma_hw_init: successfulleth0IPQ6018# ?? - alias for 'help'aq_load_fw- LOAD aq-fw-binaryaq_phy_restart- Restart Aquantia phybase - print or set address offsetbdinfo - print Board Info structurebootelf - Boot from an ELF image in memorybootipq - bootipq from flash devicebootm - boot application image from memorybootp - boot image via network using BOOTP/TFTP protocolbootvx - Boot vxWorks from an ELF imagebootz - boot Linux zImage image from memorycanary - test stack canarychpart - change active partitioncmp - memory compareconinfo - print console devices and informationcp - memory copycrc32 - checksum calculationdcache - enable or disable data cachedevinfo - device info handling commandsdhcp - boot image via network using DHCP/TFTP protocoldm - Driver model low level accessecho - echo args to consoleeditenv - edit environment variableenv - environment handling commandserase - erase FLASH memoryexectzt - execute TZTexit - exit scriptfalse - do nothing, unsuccessfullyfdt - flattened device tree utility commandsflash - flash part_name
flash part_name load_addr file_size
flasherase- flerase part_name flinfo - print FLASH memory informationfuseipq - fuse QFPROM registers from memorygo - start application at address 'addr'help - print command description/usagei2c - I2C sub-systemicache - enable or disable instruction cacheimxtract- extract a part of a multi-imageipq_mdio- IPQ mdio utility commandsis_sec_boot_enabled- check secure boot fuse is enabled or notitest - return true/false on integer compareloop - infinite loop on address rangemd - memory displaymii - MII utility commandsmm - memory modify (auto-incrementing address)mmc - MMC sub systemmmcinfo - display MMC infomtdparts- define flash/nand partitionsmtest - simple RAM read/write testmw - memory write (fill)nand - NAND sub-systemnboot - boot from NAND devicenm - memory modify (constant address)part - disk partition related commandspci - list and access PCI Configuration Spaceping - send ICMP ECHO_REQUEST to network hostprintenv- print environment variablesprotect - enable or disable FLASH write protectionreset - Perform RESET of the CPUrun - run commands in an environment variablerunmulticore- Enable and schedule secondary coressaveenv - save environment variables to persistent storagesecure_authenticate- authenticate the signed imagesetenv - set environment variablessetexpr - set environment variable as the result of eval expressionsf - SPI flash sub-systemshowvar - print local hushshell variablessleep - delay execution for some timesmeminfo- print SMEM FLASH informationsource - run script from memorytest - minimal test like /bin/shtftp - boot image via network using TFTP protocoltftpput - TFTP put command, for uploading files to a servertrue - do nothing, successfullyuart - UART sub-systemubi - ubi commandsusb - USB sub-systemusbboot - boot from USB deviceversion - print monitor, compiler and linker versionIPQ6018# versionU-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800)arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 5.2.0 unknown) 5.2.0GNU ld (GNU Binutils) 2.24.0IPQ6018# printenvaltkern=6680000auto_recovery=yesbaudrate=115200boot_part=2boot_part_ready=3boot_ver=2.3.01bootargs=console=ttyMSM0,115200n8bootcmd=i2c dev 0 && i2c probe && i2c mw 0x62 0x00 0x00 1 && i2c mw 0x62 0x01 0x05 1 && i2c mw 0x62 0x08 0x00 1 && if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fibootdelay=1bootpart1=setenv bootargs $partbootargs && nand read $loadaddr $prikern $kernsize && bootm $loadaddrbootpart2=setenv bootargs $partbootargs2 && nand read $loadaddr $altkern $kernsize && bootm $loadaddrethact=eth0ethaddr=00:03:7f:ba:db:adfdt_high=0x48500000fdtcontroladdr=4a477890flash_type=2flashimg=tftp $loadaddr $image && nand erase $prikern $imgsize && nand write $loadaddr $prikern $filesizeflashimg2=tftp $loadaddr $image && nand erase $altkern $imgsize && nand write $loadaddr $altkern $filesizeimage=mr7350.imgimgsize=5200000ipaddr=192.168.1.1kernsize=800000loadaddr=44000000machid=8030200mtddevname=fsmtddevnum=0mtdids=nand0=nand0mtdparts=mtdparts=nand0:0x4e00000@0x1880000(fs),netmask=255.255.255.0partbootargs=init=/sbin/init rootfstype=squashfs ubi.mtd=rootfs root=mtd:squashfs rootwaitpartbootargs2=init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwaitprikern=1480000serverip=192.168.1.254soc_version_major=1soc_version_minor=0stderr=serial@78B1000stdin=serial@78B1000stdout=serial@78B1000Environment size: 1505/262140 bytes
OpenWrt github.com/coolsnowwolf/openwrt-gl-ax1800 dmesg
$ ssh root@192.168.1.1 -o HostKeyAlgorithms=+ssh-rsa -o PubkeyAcceptedAlgorithms=+ssh-rsaroot@192.168.1.1's password: BusyBox v1.30.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 19.07.9, r11405-2a3558b0de -----------------------------------------------------root@OpenWrt:~# dmesg[ 0.000000] Booting Linux on physical CPU 0x0[ 0.000000] Initializing cgroup subsys cpuset[ 0.000000] Initializing cgroup subsys cpu[ 0.000000] Initializing cgroup subsys cpuacct[ 0.000000] Linux version 4.4.60 (scott@desktop) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11405-2a3558b0de) ) #0 SMP PREEMPT Wed Feb 16 20:47:59 2022[ 0.000000] Boot CPU: AArch64 Processor [51af8014][ 0.000000] Ignoring memory range 0x40000000 - 0x41000000[ 0.000000] Machine: Linksys MR7350[ 0.000000] efi: Getting EFI parameters from FDT:[ 0.000000] efi: UEFI not found.[ 0.000000] cma: dma_contiguous_reserve(limit 60000000)[ 0.000000] On node 0 totalpages: 111104[ 0.000000] DMA zone: 1736 pages used for memmap[ 0.000000] DMA zone: 0 pages reserved[ 0.000000] DMA zone: 111104 pages, LIFO batch:31[ 0.000000] psci: probing for conduit method from DT.[ 0.000000] psci: PSCIv1.0 detected in firmware.[ 0.000000] psci: Using standard PSCI v0.2 function IDs[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.[ 0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc01ef61000 s19096 r8192 d30056 u57344[ 0.000000] pcpu-alloc: s19096 r8192 d30056 u57344 alloc=14*4096[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 109368[ 0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait root=/dev/ubiblock0_0 swiotlb=1 coherent_pool=2M[ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)[ 0.000000] software IO TLB [mem 0x5fe5c000-0x5fe9c000] (0MB) mapped at [ffffffc01ee5c000-ffffffc01ee9bfff][ 0.000000] Memory: 417408K/444416K available (5134K kernel code, 485K rwdata, 2488K rodata, 224K init, 405K bss, 27008K reserved, 0K cma-reserved)[ 0.000000] Virtual kernel memory layout:[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)[ 0.000000] 0xffffffbdc0040000 - 0xffffffbdc0800000 ( 7 MB actual)[ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB)[ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc01f000000 ( 496 MB)[ 0.000000] .init : 0xffffffc0007f4000 - 0xffffffc00082c000 ( 224 KB)[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0007f3034 ( 7629 KB)[ 0.000000] .data : 0xffffffc00083a000 - 0xffffffc0008b3600 ( 486 KB)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1[ 0.000000] Preemptible hierarchical RCU implementation.[ 0.000000] Build-time adjustment of leaf fanout to 64.[ 0.000000] NR_IRQS:64 nr_irqs:64 0[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns[ 0.000418] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)[ 0.000429] pid_max: default: 32768 minimum: 301[ 0.000508] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)[ 0.000517] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)[ 0.001009] Initializing cgroup subsys io[ 0.001027] Initializing cgroup subsys memory[ 0.001055] Initializing cgroup subsys devices[ 0.001069] Initializing cgroup subsys freezer[ 0.001080] Initializing cgroup subsys net_cls[ 0.001089] Initializing cgroup subsys pids[ 0.001309] EFI services will not be available.[ 0.001333] ASID allocator initialised with 65536 entries[ 0.050529] MSM Memory Dump base table set up[ 0.050550] MSM Memory Dump apps data table set up[ 0.090111] Detected VIPT I-cache on CPU1[ 0.090150] CPU1: Booted secondary processor [51af8014][ 0.120098] Detected VIPT I-cache on CPU2[ 0.120124] CPU2: Booted secondary processor [51af8014][ 0.150125] Detected VIPT I-cache on CPU3[ 0.150149] CPU3: Booted secondary processor [51af8014][ 0.150197] Brought up 4 CPUs[ 0.150223] SMP: Total of 4 processors activated.[ 0.150233] CPU: All CPU(s) started at EL1[ 0.165694] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns[ 0.165722] futex hash table entries: 1024 (order: 5, 131072 bytes)[ 0.165945] pinctrl core: initialized pinctrl subsystem[ 0.166826] NET: Registered protocol family 16[ 0.190051] cpuidle: using governor ladder[ 0.220068] cpuidle: using governor menu[ 0.220252] NET: Registered protocol family 42[ 0.220398] vdso: 2 pages (1 code @ ffffffc000841000, 1 data @ ffffffc000840000)[ 0.221312] DMA: preallocated 2048 KiB pool for atomic allocations[ 0.221402] Read of property:soc_version_minor from node failed[ 0.221411] CPU: IPQ6018, SoC Version: 1.0[ 0.221746] IPC logging disabled[ 0.221752] IPC logging disabled[ 0.221757] IPC logging disabled[ 0.221762] IPC logging disabled[ 0.221766] IPC logging disabled[ 0.237357] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.238123] sps:sps is ready.[ 0.241012] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.248372] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 0.280862] socinfo_select_format: Unsupported format v0.13. Falling back to v0.12.[ 0.280885] socinfo_print: v0.12, id=402, ver=1.0, raw_id=313, raw_ver=0, hw_plat=8, hw_plat_ver=196610[ 0.280885] accessory_chip=0, hw_plat_subtype=0, pmic_model=0, pmic_die_revision=0 foundry_id=2 serial_number=2327779025 num_pmics=0 chip_family=0x0 raw_device_family=0x2 raw_device_number=0x17[ 0.281614] pps_core: LinuxPPS API ver. 1 registered[ 0.281621] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>[ 0.281644] PTP clock support registered[ 0.283258] rpmsg_dev_probe: No pm domain[ 0.284652] clocksource: Switched to clocksource arch_sys_counter[ 0.286860] NET: Registered protocol family 2[ 0.287236] TCP established hash table entries: 4096 (order: 3, 32768 bytes)[ 0.287285] TCP bind hash table entries: 4096 (order: 4, 65536 bytes)[ 0.287361] TCP: Hash tables configured (established 4096 bind 4096)[ 0.287407] UDP hash table entries: 256 (order: 1, 8192 bytes)[ 0.287431] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)[ 0.287576] NET: Registered protocol family 1[ 0.287615] PCI: CLS 0 bytes, default 128[ 0.293815] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.293831] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.297250] Key type asymmetric registered[ 0.297266] Asymmetric key parser 'x509' registered[ 0.297296] io scheduler noop registered[ 0.297309] io scheduler deadline registered (default)[ 0.303326] msm_rpm_log_probe: OK[ 0.303602] msm-dcc b3000.dcc: DCC XPU is not specified[ 0.303845] msm-dcc b3000.dcc: jiffies_64: 0xffff8aed, cntvct_64: 0x61e7a73[ 0.303856] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff800021e004)[ 0.303867] msm-dcc b3000.dcc: gcnt_lo: 0x061e7c9b(0xffffff800021e000)[ 0.304518] TZ SMMU State: Can't detect SMMU State[ 0.304570] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set[ 0.304793] rpmsg_dev_probe: No pm domain[ 0.305198] msm_serial 78b0000.serial: msm_serial: detected port #1[ 0.305233] msm_serial 78b0000.serial: uartclk = 24000000[ 0.305265] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 5, base_baud = 1500000) is a MSM[ 0.305537] msm_serial 78b1000.serial: msm_serial: detected port #0[ 0.305563] msm_serial 78b1000.serial: uartclk = 1843200[ 0.305589] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 6, base_baud = 115200) is a MSM[ 0.305603] msm_serial: console setup on port #0[ 1.012650] console [ttyMSM0] enabled[ 1.017562] msm_serial: driver initialized[ 1.021058] msm_serial_hsl_init: driver initialized[ 1.033463] brd: module loaded[ 1.037780] loop: module loaded[ 1.038383] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64[ 1.041129] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00, 0, 0[ 1.047781] QPIC controller hw version Major:1, Minor:5[ 1.053634] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa[ 1.058527] nand: ONFI 10-Compliant Macronix MX30UF2G18AC[ 1.065085] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64[ 1.070450] 20 ofpart partitions found on MTD device qcom_nand.0[ 1.077843] Creating 20 MTD partitions on "qcom_nand.0":[ 1.083997] 0x000000000000-0x000000180000 : "0:SBL1"[ 1.091071] 0x000000180000-0x000000280000 : "0:MIBIB"[ 1.095551] 0x000000280000-0x000000600000 : "0:QSEE"[ 1.102261] 0x000000600000-0x000000680000 : "0:DEVCFG"[ 1.105186] 0x000000680000-0x000000700000 : "0:RPM"[ 1.110139] 0x000000700000-0x000000780000 : "0:CDT"[ 1.114923] 0x000000780000-0x000000800000 : "0:APPSBLENV"[ 1.119763] 0x000000800000-0x000000980000 : "0:APPSBL"[ 1.126051] 0x000000980000-0x000000a00000 : "0:ART"[ 1.130402] 0x000000a00000-0x000001300000 : "0:WIFIFW"[ 1.140956] 0x000001300000-0x000001380000 : "0:ETHPHYFW"[ 1.141927] 0x000001380000-0x000001400000 : "u_env"[ 1.146306] 0x000001400000-0x000001440000 : "s_env"[ 1.150704] 0x000001440000-0x000001480000 : "devinfo"[ 1.155578] 0x000001480000-0x000006680000 : "kernel"[ 1.218653] 0x000001c80000-0x000006680000 : "rootfs"[ 1.271415] mtd: device 15 (rootfs) set to be root filesystem[ 1.271669] mtdsplit: no squashfs found in "rootfs"[ 1.276153] 0x000006680000-0x00000b880000 : "alt_kernel"[ 1.339189] 0x000006e80000-0x00000b880000 : "alt_rootfs"[ 1.392149] 0x00000b880000-0x00000ba80000 : "sysdiag"[ 1.394186] 0x00000ba80000-0x00000fe80000 : "syscfg"[ 1.445064] libphy: Fixed MDIO Bus: probed[ 1.665764] qca-mdio 90000.mdio: Could not find phy-reset-gpio[ 1.665878] libphy: qca_mdio: probed[ 1.671610] qca-mdio 90000.mdio: qca-mdio driver was registered[ 1.674336] i2c /dev entries driver[ 1.715146] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com[ 1.715603] sdhci: Secure Digital Host Controller Interface driver[ 1.722644] sdhci: Copyright(c) Pierre Ossman[ 1.728656] sdhci-pltfm: SDHCI platform and OF driver helper[ 1.733975] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed[ 1.738865] ICE IRQ = 17[ 1.748607] [ 1.748607] Version Rollback Feature Disabled[ 1.751756] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available[ 1.755794] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000[ 1.761868] coresight-csr 6001000.csr: CSR initialized[ 1.769608] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000[ 1.774530] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000[ 1.782105] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000[ 1.789483] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000[ 1.796858] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000[ 1.804213] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000[ 1.811611] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000[ 1.818984] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000[ 1.826361] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000[ 1.833731] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000[ 1.841121] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000[ 1.848488] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000[ 1.855875] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000[ 1.863238] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000[ 1.870634] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000[ 1.878010] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000[ 1.885384] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000[ 1.892885] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000[ 1.900256] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000[ 1.907666] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000[ 1.915075] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000[ 1.922418] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006064000[ 1.929524] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006064000[ 1.946617] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006064000[ 1.962501] sps:BAM 0x0000000006064000 is registered.<6>[ 1.970178] coresight-tmc 6048000.tmc: TMC initialized[ 1.974943] coresight-tmc 6047000.tmc: TMC initialized[ 1.980068] coresight-funnel 6041000.funnel: FUNNEL initialized[ 1.985110] coresight-funnel 6100000.funnel: FUNNEL initialized[ 1.990914] coresight-funnel 6130000.funnel: FUNNEL initialized[ 1.996829] coresight-funnel 6120000.funnel: FUNNEL initialized[ 2.002732] coresight-funnel 61a1000.funnel: FUNNEL initialized[ 2.009157] coresight-etm4x 619c000.etm: ETM 4.0 initialized[ 2.014871] coresight-etm4x 619d000.etm: ETM 4.0 initialized[ 2.020773] coresight-etm4x 619e000.etm: ETM 4.0 initialized[ 2.026479] coresight-etm4x 619f000.etm: ETM 4.0 initialized[ 2.031743] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized[ 2.037490] coresight-stm 6002000.stm: STM initialized[ 2.046045] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000[ 2.049916] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized[ 2.058494] NET: Registered protocol family 10[ 2.065739] NET: Registered protocol family 17[ 2.069379] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.[ 2.073810] Bridge firewalling registered[ 2.086555] 8021q: 802.1Q VLAN Support v1.8[ 2.091711] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 2.095697] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 2.101860] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0[ 2.109057] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2[ 2.115644] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0[ 2.123278] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable[ 2.130805] cpr3_mem_acc_init: apc: not using memory accelerator regulator[ 2.139934] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 675000 uV[ 2.146883] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 787500 uV[ 2.156864] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 850000 uV[ 2.166673] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 925000 uV[ 2.176515] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 535, quot_offset[ 7]= 0[ 2.186297] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 719, quot_offset[ 7]= 180[ 2.197145] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]= 814, quot_offset[ 7]= 95[ 2.208084] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]= 926, quot_offset[ 7]= 110[ 2.219261] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop[ 2.231504] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz[ 2.237382] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 864000 KHz[ 2.245308] ubi0: attaching mtd17[ 2.321182] random: nonblocking pool is initialized[ 2.541192] ubi0: scanning is finished[ 2.546661] ubi0: attached mtd17 (name "alt_rootfs", size 74 MiB)[ 2.546684] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 2.551724] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 2.558508] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096[ 2.565360] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0[ 2.572122] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128[ 2.578382] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 752153478[ 2.585417] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 40[ 2.594361] ubi0: background thread "ubi_bgt0d" started, PID 135[ 2.595196] block ubiblock0_0: created from ubi0:0(rootfs)[ 2.611602] VFS: Mounted root (squashfs filesystem) readonly on device 252:0.[ 2.615577] Freeing unused kernel memory: 224K (ffffffc0007f4000 - ffffffc00082c000)[ 2.622492] Freeing alternatives memory: 40K (ffffffc00082c000 - ffffffc000836000)[ 2.806673] init: Console is alive[ 2.806773] init: - watchdog -[ 3.244309] kmodloader: loading kernel modules from /etc/modules-boot.d/*[ 3.255584] kmodloader: done loading kernel modules from /etc/modules-boot.d/*[ 3.262433] init: - preinit -[ 7.738827] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 230[ 7.767631] UBIFS (ubi0:1): recovery needed[ 7.851957] UBIFS (ubi0:1): recovery completed[ 7.852042] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"[ 7.855407] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes[ 7.863259] UBIFS (ubi0:1): FS size: 61329408 bytes (58 MiB, 483 LEBs), journal size 3047424 bytes (2 MiB, 24 LEBs)[ 7.873098] UBIFS (ubi0:1): reserved for root: 2896739 bytes (2828 KiB)[ 7.883334] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID 45DD6BFE-3A6C-4F31-8985-60D4B36FF509, small LPT model[ 7.892718] mount_root: switching to ubifs overlay[ 7.909792] urandom-seed: Seeding with /etc/urandom.seed[ 7.938016] procd: - early -[ 7.938064] procd: - watchdog -[ 8.568473] procd: - watchdog -[ 8.568613] procd: - ubus -[ 8.622104] procd: - init -[ 8.793199] kmodloader: loading kernel modules from /etc/modules.d/*[ 8.827236] urngd: v1.0.2 started.[ 8.850103] ssdk_switch_device_num_init[1159]:INFO:ess-switch dts node number: 1[ 8.850176] ssdk_dt_get_switch_node[970]:INFO:ess-switch DT exist![ 8.856582] ssdk_dt_parse_access_mode[856]:INFO:switch_access_mode: local bus[ 8.862550] ssdk_dt_parse_access_mode[869]:INFO:switchreg_base_addr: 0x3a000000[ 8.869761] ssdk_dt_parse_access_mode[870]:INFO:switchreg_size: 0x1000000[ 8.876889] ssdk_dt_parse_mac_mode[295]:INFO:mac mode = 0x0[ 8.883813] ssdk_dt_parse_mac_mode[304]:INFO:mac mode1 = 0xff[ 8.889202] ssdk_dt_parse_mac_mode[313]:INFO:mac mode2 = 0xff[ 8.895149] ssdk_dt_parse_uniphy[332]:INFO:ess-uniphy DT exist![ 8.900939] ssdk_dt_parse_intf_mac[801]:INFO:dp1 MAC 00:03:7f:ba:db:ad[ 8.906697] ssdk_plat_init start[ 8.985733] ssdk_gcc_clock_init[1033]:INFO:SSDK gcc clock init successfully![ 8.986204] HPPE initializing...[ 8.991990] malibu_phy_api_ops_init[2848]:INFO:qca probe malibu phy driver succeeded![ 8.998609] regi_init[3567]:INFO:Initializing HPPE!![ 9.214651] ssdk_ppe_reset_init[1265]:INFO:ppe reset successfully![ 9.217271] qca_hppe_tdm_hw_init[684]:INFO:tdm setup num=96[ 9.219947] qca_hppe_portctrl_hw_init[107]:INFO:Cypress PPE port initializing[ 9.335178] __adpt_hppe_uniphy_psgmii_mode_set[635]:INFO:uniphy 0 psgmii channel selection[ 9.548872] ssdk_switch_register[1718]:INFO:Chip version 0x1501[ 9.548907] qca_link_polling_select[1315]:INFO:link-polling-required node does not exist[ 9.553591] ssdk_switch_register[1744]:INFO:polling is selected[ 9.561933] regi_init[3571]:INFO:Initializing HPPE Done!![ 9.567621] regi_init[3631]:INFO:qca-ssdk module init succeeded![ 9.575004] EDMA ver 1 hw init[ 9.579410] EDMA HW Reset completed succesfully[ 9.582089] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23)[ 9.586518] RxDesc:1 (15-15) RxFill:1 (7-7)[ 9.593716] GMAC2(ffffffc01b8fe880) Invalid MAC@ - using 3a:49:d8:a8:07:32[ 9.597253] GMAC3(ffffffc01b8a2880) Invalid MAC@ - using 5a:f5:2d:11:6e:1a[ 9.604059] GMAC4(ffffffc01b8a6880) Invalid MAC@ - using 1e:8d:5f:06:15:d7[ 9.610940] GMAC5(ffffffc01c78a880) Invalid MAC@ - using 0e:65:ef:a3:ab:8c[ 9.617835] **********************************************************[ 9.623554] * NSS Data Plane driver[ 9.630115] **********************************************************[ 9.634899] l2tp_core: L2TP core driver, V2.0[ 9.640455] l2tp_netlink: L2TP netlink interface[ 9.763513] nss_driver - fw of size 860224 bytes copied to load addr: 40000000, nss_id : 0[ 9.765440] Supported Frequencies - [ 9.770935] 187.2 MHz 748.8 MHz [ 9.776689] 1.4976 GHz <1>[ 9.777600] [ 9.779986] ffffffbffc195e00: set sdma ffffffc01bb69100[ 9.781533] node size 2 # items 4[ 9.786407] memory: 40000000 536870912 (avl 439615488) items 4 active_cores 1[ 9.789858] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000[ 9.797000] ffffffbffc195e00: NSS core 0 DDR from 40000000 to 41000000[ 9.803862] ffffffbffc195e00: meminfo init succeed[ 9.826444] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)[ 9.829964] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 9.833516] Netfilter messages via NETLINK v0.30.[ 9.838023] ip_set: protocol 6[ 9.850765] PPP generic driver version 2.4.2[ 9.851333] NET: Registered protocol family 24[ 9.854140] node size 2 # items 4[ 9.854146] memory: 40000000 536870912 (avl 439730176) items 4 active_cores 1[ 9.854152] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000[ 9.854156] ffffffbffc195e00: nss core 0 booted successfully[ 9.878984] nss_wifi_meshmgr_init_module[1866]:Module Build Id: 04/23/23, 09:35:05 loaded[ 9.883553] Loading modules backported from Linux version v3.18-503864-g787674a[ 9.889999] Backport generated by backports.git v5.10-rc6-1-1-g79f0741[ 9.898202] ip_tables: (C) 2000-2006 Netfilter Core Team[ 9.905222] l2tp_ppp: PPPoL2TP kernel driver, V2.0[ 9.911131] nf_conntrack version 0.5.0 (3263 buckets, 13052 max)[ 10.056936] xt_FULLCONENAT: RFC3489 Full Cone NAT module[ 10.056936] xt_FULLCONENAT: Copyright (C) 2018 Chion Tang <tech@chionlab.moe>[ 10.072100] xt_time: kernel timezone is -0000[ 10.132476] ath11k c000000.wifi: Not multipd architecture[ 10.134993] ath11k c000000.wifi: ipq6018 hw1.0[ 10.137235] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss[ 10.141370] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340[ 11.034038] Subsystem error monitoring/handling services are up[ 11.034329] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up[ 11.034520] rpmsg_dev_probe: No pm domain[ 11.034700] rpmsg_dev_probe: No pm domain[ 11.045205] ------------[ cut here ]------------[ 11.045208] WARNING: at arch/arm64/mm/ioremap.c:58[ 11.045279] Modules linked in: ath11k_ahb(+) ath11k_pci ath11k nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_quota xt_pkttype xt_physdev xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_LOG xt_FULLCONENAT ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack l2tp_ppp iptable_mangle iptable_filter ip_tables crc_ccitt compat qca_nss_wifi_meshmgr qca_nss_pppoe pppoe pppox ppp_generic slhc xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 bonding qca_nss_drv l2tp_netlink l2tp_core udp_tunnel ip6_udp_tunnel qca_nss_dp qca_ssdk leds_gpio gpio_button_hotplug[ 11.045309] [ 11.045314] CPU: 1 PID: 1011 Comm: kworker/u8:3 Not tainted 4.4.60 #0[ 11.045315] Hardware name: Linksys MR7350 (DT)[ 11.045327] Workqueue: qmi_msg_handler qmi_data_ready_work[ 11.045329] task: ffffffc01bbcbf00 ti: ffffffc01bbcbf00 task.ti: ffffffc01bbcbf00[ 11.045336] PC is at __ioremap_caller+0x70/0xe8[ 11.045339] LR is at __ioremap_caller+0x6c/0xe8[ 11.045341] pc : [<ffffffc000091690>] lr : [<ffffffc00009168c>] pstate: 80000145[ 11.045342] sp : ffffffc01b457a80[ 11.045346] x29: ffffffc01b457a80 x28: ffffffc019ee1a40 [ 11.045349] x27: ffffffc01b457b50 x26: ffffffc01db0f010 [ 11.045352] x25: ffffffc019ef2000 x24: ffffffc019ee0018 [ 11.045355] x23: 00e8000000000707 x22: ffffffbffc5365b4 [ 11.045358] x21: 0000000000000000 x20: 0000000050100000 [ 11.045361] x19: 0000000000100000 x18: 0000000002d9a328 [ 11.045364] x17: 0000000003da017d x16: 0000000092d322d9 [ 11.045367] x15: 000000004bf7025e x14: 0fffffffffffffff [ 11.045370] x13: 0000000000000020 x12: 0101010101010101 [ 11.045372] x11: 0000000000000006 x10: 0101010101010101 [ 11.045376] x9 : ffffffffffffffff x8 : 7f7f7f7f7f7f7f7f [ 11.045379] x7 : 0000000000000018 x6 : 0000000011c00000 [ 11.045382] x5 : ffffffc0008e0fc8 x4 : 0000000000000002 [ 11.045385] x3 : 0000000000000002 x2 : 0000000060000000 [ 11.045387] x1 : 0000000000000001 x0 : 0000000000000001 [ 11.045388] [ 11.045390] ---[ end trace 51419203dbb5c34d ]---[ 11.045391] Call trace:[ 11.045395] [<ffffffc000091690>] __ioremap_caller+0x70/0xe8[ 11.045398] [<ffffffc000091718>] __ioremap+0x10/0x18[ 11.045420] [<ffffffbffc5365b4>] ath11k_htc_init+0x202c/0x2378 [ath11k][ 11.045424] [<ffffffc0002f7f28>] qmi_invoke_handler+0x88/0xf0[ 11.045427] [<ffffffc0002f81cc>] qmi_handle_message+0x23c/0x308[ 11.045430] [<ffffffc0002f8b6c>] qmi_data_ready_work+0x3e4/0x408[ 11.045436] [<ffffffc0000aa560>] process_one_work+0x1f8/0x330[ 11.045439] [<ffffffc0000aa8f4>] worker_thread+0x25c/0x438[ 11.045444] [<ffffffc0000b0230>] kthread+0xd0/0xe0[ 11.045448] [<ffffffc000085540>] ret_from_fork+0x10/0x50[ 11.045942] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff[ 11.045946] ath11k c000000.wifi: fw_version 0x2506844c fw_build_timestamp 2021-07-13 11:09 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1[ 11.066512] ath11k c000000.wifi: qmi caldata downloaded: type: 2[ 13.856279] remoteproc remoteproc0: stopped remote processor cd00000.qcom_q6v5_wcss[ 13.856317] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss[ 13.862873] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340[ 14.168138] Subsystem error monitoring/handling services are up[ 14.168430] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up[ 14.168617] rpmsg_dev_probe: No pm domain[ 14.168861] rpmsg_dev_probe: No pm domain[ 14.185342] ------------[ cut here ]------------[ 14.186308] kmodloader: done loading kernel modules from /etc/modules.d/*[ 14.193522] WARNING: at arch/arm64/mm/ioremap.c:58[ 14.200200] Modules linked in: iptable_nat nf_nat_ipv4 ath11k_ahb ath11k_pci ath11k nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_quota xt_pkttype xt_physdev xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_LOG xt_FULLCONENAT ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack l2tp_ppp iptable_mangle iptable_filter ip_tables crc_ccitt compat qca_nss_wifi_meshmgr qca_nss_pppoe pppoe pppox ppp_generic slhc xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 bonding qca_nss_drv l2tp_netlink l2tp_core udp_tunnel ip6_udp_tunnel qca_nss_dp qca_ssdk leds_gpio gpio_button_hotplug[ 14.306441] [ 14.306798] CPU: 2 PID: 1011 Comm: kworker/u8:3 Tainted: G W 4.4.60 #0[ 14.308366] Hardware name: Linksys MR7350 (DT)[ 14.315749] Workqueue: qmi_msg_handler qmi_data_ready_work[ 14.325715] task: ffffffc01bbcbf00 ti: ffffffc01bbcbf00 task.ti: ffffffc01bbcbf00[ 14.325819] PC is at __ioremap_caller+0x70/0xe8[ 14.333276] LR is at __ioremap_caller+0x6c/0xe8[ 14.337614] pc : [<ffffffc000091690>] lr : [<ffffffc00009168c>] pstate: 80000145[ 14.342133] sp : ffffffc01b457a80[ 14.349763] x29: ffffffc01b457a80 x28: ffffffc019ee1a40 [ 14.358091] x27: ffffffc01b457b50 x26: ffffffc01db0f010 [ 14.363386] x25: ffffffc019ef2000 x24: ffffffc019ee0018 [ 14.368682] x23: 00e8000000000707 x22: ffffffbffc5365b4 [ 14.373977] x21: 0000000000000000 x20: 0000000050100000 [ 14.379272] x19: 0000000000100000 x18: 0000000000000000 [ 14.384568] x17: 0000000000001800 x16: 0000000000001400 [ 14.389862] x15: 000000000000000c x14: 011b010001180100 [ 14.395158] x13: 0117010001164b4e x12: 454c000415010001 [ 14.400453] x11: 0000000000000006 x10: 0101010101010101 [ 14.405749] x9 : ffffffffffffffff x8 : 7f7f7f7f7f7f7f7f [ 14.411043] x7 : 0000000000000018 x6 : 0000000011c00000 [ 14.416337] x5 : ffffffc0008e0fc8 x4 : 0000000000000002 [ 14.421633] x3 : 0000000000000002 x2 : 0000000060000000 [ 14.426928] x1 : 0000000000000001 x0 : 0000000000000001 [ 14.432223] [ 14.432399] ---[ end trace 51419203dbb5c34e ]---[ 14.433969] Call trace:[ 14.438578] [<ffffffc000091690>] __ioremap_caller+0x70/0xe8[ 14.440742] [<ffffffc000091718>] __ioremap+0x10/0x18[ 14.446317] [<ffffffbffc5365b4>] ath11k_htc_init+0x202c/0x2378 [ath11k][ 14.451511] [<ffffffc0002f7f28>] qmi_invoke_handler+0x88/0xf0[ 14.457857] [<ffffffc0002f81cc>] qmi_handle_message+0x23c/0x308[ 14.463747] [<ffffffc0002f8b6c>] qmi_data_ready_work+0x3e4/0x408[ 14.469479] [<ffffffc0000aa560>] process_one_work+0x1f8/0x330[ 14.475727] [<ffffffc0000aa8f4>] worker_thread+0x25c/0x438[ 14.481369] [<ffffffc0000b0230>] kthread+0xd0/0xe0[ 14.486764] [<ffffffc000085540>] ret_from_fork+0x10/0x50[ 14.493004] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff[ 14.497035] ath11k c000000.wifi: fw_version 0x2506844c fw_build_timestamp 2021-07-13 11:09 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1[ 14.509773] ath11k c000000.wifi: qmi caldata downloaded: type: 2[ 14.624633] applying ath11k-macs[ 15.372665] ECM init[ 15.372722] ECM database jhash random seed: 0x7152bdea[ 15.375194] ECM init complete[ 15.927246] configuring additional NSS pbufs[ 15.937854] additional pbufs of size 3100672 got added to NSS[ 16.182347] device eth0 entered promiscuous mode[ 16.183172] br-lan: port 1(eth0) entered forwarding state[ 16.186099] br-lan: port 1(eth0) entered forwarding state[ 16.199021] device eth1 entered promiscuous mode[ 16.199089] br-lan: port 2(eth1) entered forwarding state[ 16.202743] br-lan: port 2(eth1) entered forwarding state[ 16.210494] device eth2 entered promiscuous mode[ 16.213478] br-lan: port 3(eth2) entered forwarding state[ 16.218139] br-lan: port 3(eth2) entered forwarding state[ 16.225818] device eth3 entered promiscuous mode[ 16.228833] br-lan: port 4(eth3) entered forwarding state[ 16.233475] br-lan: port 4(eth3) entered forwarding state[ 16.242656] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready[ 16.594862] nss-dp 3a001200.dp2 eth1: PHY Link up speed: 1000[ 16.614806] nss-dp 3a001800.dp5 eth4: PHY Link up speed: 1000[ 16.614883] IPv6: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready[ 16.701722] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready[ 16.703788] device wlan0 entered promiscuous mode[ 16.706832] br-lan: port 5(wlan0) entered forwarding state[ 16.711376] br-lan: port 5(wlan0) entered forwarding state[ 16.771613] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready[ 16.773206] device wlan1 entered promiscuous mode[ 16.776620] br-lan: port 6(wlan1) entered forwarding state[ 16.781256] br-lan: port 6(wlan1) entered forwarding state[ 16.889372] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready[ 17.174698] br-lan: port 1(eth0) entered disabled state[ 17.174934] br-lan: port 3(eth2) entered disabled state[ 17.178830] br-lan: port 4(eth3) entered disabled state[ 17.184019] br-lan: port 5(wlan0) entered disabled state[ 17.200873] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready[ 17.201001] br-lan: port 5(wlan0) entered forwarding state[ 17.206333] br-lan: port 5(wlan0) entered forwarding state[ 18.194660] br-lan: port 2(eth1) entered forwarding state[ 18.774661] br-lan: port 6(wlan1) entered forwarding state[ 19.204658] br-lan: port 5(wlan0) entered forwarding state[ 4250.565146] device wlan1 left promiscuous mode[ 4250.565213] br-lan: port 6(wlan1) entered disabled state[ 4251.679068] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready[ 4251.681014] device wlan1 entered promiscuous mode[ 4251.684173] br-lan: port 6(wlan1) entered forwarding state[ 4251.688715] br-lan: port 6(wlan1) entered forwarding state[ 4251.701557] br-lan: port 6(wlan1) entered disabled state[ 4251.719209] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready[ 4251.719372] br-lan: port 6(wlan1) entered forwarding state[ 4251.724739] br-lan: port 6(wlan1) entered forwarding state[ 4253.721421] br-lan: port 6(wlan1) entered forwarding state[ 4261.871810] device wlan0 left promiscuous mode[ 4261.871875] br-lan: port 5(wlan0) entered disabled state[ 4262.731480] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready[ 4262.733633] device wlan0 entered promiscuous mode[ 4262.736571] br-lan: port 5(wlan0) entered forwarding state[ 4262.741160] br-lan: port 5(wlan0) entered forwarding state[ 4262.911433] br-lan: port 5(wlan0) entered disabled state[ 4263.092660] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready[ 4263.092833] br-lan: port 5(wlan0) entered forwarding state[ 4263.098129] br-lan: port 5(wlan0) entered forwarding state[ 4265.091379] br-lan: port 5(wlan0) entered forwarding state[ 4354.850386] device wlan0 left promiscuous mode[ 4354.850461] br-lan: port 5(wlan0) entered disabled state[ 4355.656826] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready[ 4355.658912] device wlan0 entered promiscuous mode[ 4355.661791] br-lan: port 5(wlan0) entered forwarding state[ 4355.666464] br-lan: port 5(wlan0) entered forwarding state[ 4355.891080] br-lan: port 5(wlan0) entered disabled state[ 4356.013951] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready[ 4356.014102] br-lan: port 5(wlan0) entered forwarding state[ 4356.019411] br-lan: port 5(wlan0) entered forwarding state[ 4358.011007] br-lan: port 5(wlan0) entered forwarding state
Notes
Firmware download
Tags
How to add tags
ipq807x, ipq6018, 256nand, 512ram, 5port, gigabitethernet, 802.11bgn, 802.11ax, 2ant, 2wnic, 1usb, usb3.0, 4core, serial, 12v powered, Unsupported devices
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
![[OpenWrt Wiki] Linksys MR7350 1.0 (2024)](data:image/png;base64,iVBORw0KGgoAAAANSUhEUgAAAAEAAAABCAQAAAC1HAwCAAAAC0lEQVR42mP8/h8AAvMB+NzmkbcAAAAASUVORK5CYII=)