Not supported.
The TP-Link X80-5G has the following buttons:
| BUTTON | Event |
|---|---|
| Reset | reset/ recover |
| Architecture | ARMv8-A (aarch64 Cortex A53, 4 cores) |
|---|---|
| Vendor | Qualcomm |
| Bootloader | U-Boot (2016) |
| System-On-Chip | Qualcomm IPQ8074A (Networking Pro 1210 platform) |
| CPU/Speed | 2.2GHZ |
| Flash-Chip | ESMT F59D1G81MB-45TI 1G-bit NAND |
| Flash MB | 128MB (1Gbit) |
| RAM-chip | 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit) |
| RAM MB | 512MB (4Gbit) |
| WLan System-On-Chip (5g) | Qualcomm QCN5054 |
| WLan Front end modules (5g) | 8* Qorvo QPF4588 |
| WLAN (5G) | A/N/AC/AX |
| WLAN Antenna (int) | 8* (4 shared with 2.5G) |
| WLan System-On-Chip (2.4G) | Qualcomm QCN5024 |
| WLan Front end modules (2.4G) | 4* Skyworks SKY85340-11 |
| WLAN (2.4G) | B/G/N/AX |
| WLAN Antenna (int) | 4* (shared with 5g) |
| Eithernet-phy (1Gbit) | Qualcomm (Atheros) AR8033-AL1A |
| Ethernet (1Gbit) | 1* |
| Eithernet-phy (2.5Gbit) | Qualcomm QCA8081 |
| Ethernet (2.5Gbit) | 1* |
| Switch | Embedded in the SOC? |
| Serial | 1.8v 8n1 (testpoints) |
| Modem System-On-Chip | Qualcomm 5G RG50xQ (Snapdragon X55 platform) |
| 5G modem capability | 5000Mbps down 900Mbps up |
| 5G modem bands | N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79 |
| 4G modem capability | 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps) |
| 4G modem FDD bands | B1/B3/B5/B7/B8/B18/B19/B20/B26/B28 |
| 4G modem TDD bands | B34/B38/B39/B40/B41/B42/B43 |
| Modem antenna (int) | 8* (5G/4G use) |
| Modem antenna (ext) | 2* SMA connectors (5G/4G use) |
| SIM type | 1* Nano SIM |
| Telephony | 1* POTS RJ11 |
dev: size erasesize namemtd0: 00100000 00020000 "0:SBL1"mtd1: 00100000 00020000 "0:MIBIB"mtd2: 00080000 00020000 "0:BOOTCONFIG"mtd3: 00080000 00020000 "0:BOOTCONFIG1"mtd4: 00300000 00020000 "0:QSEE"mtd5: 00080000 00020000 "0:DEVCFG"mtd6: 00080000 00020000 "0:APDP"mtd7: 00080000 00020000 "0:RPM"mtd8: 00080000 00020000 "0:CDT"mtd9: 00180000 00020000 "0:APPSBLENV"mtd10: 00200000 00020000 "0:APPSBL"mtd11: 00080000 00020000 "0:ART"mtd12: 02a00000 00020000 "rootfs"mtd13: 02a00000 00020000 "rootfs_1"mtd14: 00080000 00020000 "0:ETHPHYFW"mtd15: 00900000 00020000 "factory_data"mtd16: 01100000 00020000 "runtime_data"mtd17: 00573000 0001f000 "kernel"mtd18: 01341000 0001f000 "ubi_rootfs"
Back ports
Bottom and label
PCB's
It has a top cover you pry off to see the fan which exposes four screws two for each clam shell o part of the case.Underneath it has four rubber feet with screws beneath I just forced my screw-driver through the rubber pad to save removing them.With all 8 screws removed you may split off both sides of the shell.On the side of the shell with the RGB info LED it has a small PCB with a harness with a push in connector that needs removing on the bottom of the device before separating.At this point you have enough to expose the serial UART and I really would not recommend you proceed any further.To completely disassemble the device, one must unsolder at least one of the two antennas labeled 1 and 2 and slide the PCB up from the top fan assembly.Behind the antennas 1 and 2 is 2 screws to remove the fan assembly.once the fan assembly is lifted up you can unplug the fan connector to remove it.You then can start to separate the two PCB's of the device there is there is 14 IPEX/ U.FL connectors 8 for the WIFI and 8 for the LTE, They are all labeled on the PCB and the antennas.All the U.Fl cables are secured with spring clips and tape and plastic hooks I'd recommend you take pictures as it was a pain to work out how to route them to get it together again.With all the antenna connectors unplugged you can then remove the screws holding the heatsinks PCB's and antenna Frames.NOTE all the screws are of different lengths make sure to note their location for reassembly.Separating the two halves this will expose the bottom 2 cover screws to remove the base.
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labeled TP1 TP2 and TP3.
I soldered a standard pin header to the test pads but be aware it is very fragile and would be easy to rip them off by accident but seems sturdy with TP3 being on a ground plane.
Green is Ground (tp3)Yellow is RX (tp2)Orange is TX (tp1)
R (~10k Ohms) ------------- /---\/\/\/`--VCC ---| USB FTDI | ----------- | | 1.8V | |TP2|-- RX --------+----------- TX ----| | --> to PC (minicom, screen, C-Kermit, ...) |TP1|-- TX -------------------- RX ----| | |TP3|-- GND ------------------ GND ----| | ----------- -------------
| Serial connection parameters for TP-Link X80-5G V1 | 115200, 8N1, 1.8V |
|---|
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158S - IMAGE_VARIANT_STRING=HAACANAZAS - OEM_IMAGE_VERSION_STRING=CRMS - Boot Config, 0x000002e5B - 201 - PBL, StartB - 2736 - bootable_media_detect_entry, StartB - 3444 - bootable_media_detect_success, StartB - 3448 - elf_loader_entry, StartB - 6116 - auth_hash_seg_entry, StartB - 6359 - auth_hash_seg_exit, StartB - 68381 - elf_segs_hash_verify_entry, StartB - 131223 - PBL, EndB - 142282 - SBL1, StartB - 194132 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4B - 200598 - pm_device_init, StartB - 321714 - PM_SET_VAL:SkipD - 120658 - pm_device_init, DeltaB - 324123 - pm_driver_init, StartD - 5368 - pm_driver_init, DeltaB - 330498 - clock_init, StartD - 2135 - clock_init, DeltaB - 334432 - boot_flash_init, StartD - 12566 - boot_flash_init, DeltaB - 350780 - boot_config_data_table_init, StartD - 3111 - boot_config_data_table_init, Delta - (575 Bytes)B - 358283 - Boot Setting : 0x00000618B - 362187 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:4,Subtype:0B - 369111 - sbl1_ddr_set_params, StartB - 372923 - CPR configuration: 0x30cB - 376278 - cpr_init, StartB - 379176 - Rail:0 Mode: 5 Voltage: 792000B - 384269 - CL CPR settled at 744000mVB - 387106 - Rail:1 Mode: 5 Voltage: 880000B - 391376 - Rail:1 Mode: 7 Voltage: 888000D - 16531 - cpr_init, DeltaB - 398177 - Pre_DDR_clock_init, StartB - 402264 - Pre_DDR_clock_init, EndB - 405589 - DDR Type : PCDDR3B - 411323 - do ddr sanity test, StartD - 1067 - do ddr sanity test, DeltaB - 416081 - DDR: Start of HAL DDR Boot TrainingB - 420808 - DDR: End of HAL DDR Boot TrainingB - 426512 - DDR: Checksum to be stored on flash is 1377291785B - 436821 - Image Load, StartD - 224327 - QSEE Image Loaded, Delta - (1376448 Bytes)B - 661240 - Image Load, StartD - 61 - SEC Image Loaded, Delta - (0 Bytes)B - 668926 - Image Load, StartD - 10705 - DEVCFG Image Loaded, Delta - (26008 Bytes)B - 679723 - Image Load, StartD - 22051 - RPM Image Loaded, Delta - (86584 Bytes)B - 701866 - Image Load, StartD - 108976 - APPSBL Image Loaded, Delta - (672668 Bytes)B - 810964 - QSEE Execution, StartD - 61 - QSEE Execution, DeltaB - 816759 - USB D+ check, StartD - 0 - USB D+ check, DeltaB - 823164 - SBL1, EndD - 683170 - SBL1, DeltaS - Flash Throughput, 6745 KB/s (2162955 Bytes, 320641 us)S - DDR Frequency, 466 MHzS - Core 0 Frequency, 1651 MHzU-Boot 2016.01 (Feb 25 2021 - 20:16:45 +0800)DRAM: smem ram ptable found: ver: 1 len: 41 GiBNAND: Could not find nand_gpio in dts, using defaultsONFI device foundID = 158061c8Vendor = c8Device = 61SF: Unsupported flash IDs: manuf 00, jedec 1c78, ext_jedec 4a74ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)128 MiBMMC: <NULL>: 0PCI0 is not defined in the device treePCI1 is not defined in the device treeIn: serial@78B3000Out: serial@78B3000Err: serial@78B3000machid: 8010400Card did not respond to voltage select!eth0 MAC Address from ART is not valideth1 MAC Address from ART is not valideth2 MAC Address from ART is not valideth3 MAC Address from ART is not valideth4 MAC Address from ART is not valideth5 MAC Address from ART is not validgpio 38 set BOARD_3V9_5V_EN_GPIO to high[1] gpio 64 set PHY_QCA8081_1V8_EN_GPIO to high[1] gpio 33 set PHY_AR8033_3V3_EN_GPIO to high[1] gpio 35 set ONOFF_MODULE_5G_GPIO to low[0] ... 1s gpio 35 set ONOFF_MODULE_5G_GPIO to high[1]ubi0: attaching mtd1ubi0: scanning is finishedubi0: attached mtd1 (name "mtd=0", size 9 MiB)ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytesubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096ubi0: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128ubi0: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1097309032ubi0: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20Find no boot alter flag!Enter magic string to stop autoboot in?Unmounting UBIFS volume ubi_factory_data!ubi0: detaching mtd1ubi0: mtd1 is detachedubi0: attaching mtd1ubi0: scanning is finishedubi0: attached mtd1 (name "mtd=0", size 42 MiB)ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytesubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 273099923ubi0: available PEBs: 108, total reserved PEBs: 228, PEBs reserved for bad PEB handling: 20Read 0 bytes from volume kernel to 44000000No size specified -> Using max size (5713920)## Loading kernel from FIT Image at 44000000 ... Using 'config@hk01.c5' configuration Trying 'kernel@1' kernel subimage Description: ARM64 OpenWrt Linux-4.4.60 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e8 Data Size: 3857929 Bytes = 3.7 MiB Architecture: AArch64 OS: Linux Load Address: 0x41080000 Entry Point: 0x41080000 Hash algo: crc32 Hash value: db19bb74 Hash algo: sha1 Hash value: 80e8e02e244a73839be2d7cb2a6f845e49cb0cc8 Verifying Hash Integrity ... crc32+ sha1+ OK## Loading fdt from FIT Image at 44000000 ... Using 'config@hk01.c5' configuration Trying 'fdt@hk01.c5' fdt subimage Description: ARM64 OpenWrt qcom-ipq807x-hkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x443d8698 Data Size: 92380 Bytes = 90.2 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 3f191698 Hash algo: sha1 Hash value: d0cbc4e75fecf605333dd4a95c21ed37d26c3df4 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x443d8698 Uncompressing Kernel Image ... OK Loading Device Tree to 4a3e6000, end 4a3ff8db ... OKCould not find PCI in device treeUsing machid 0x8010400 from environmentStarting kernel ...Jumping to AARCH64 kernel via monitor[ 0.000000] Booting Linux on physical CPU 0x0[ 0.000000] Linux version 4.4.60 (tplink@linuxci2-sp) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 34c568b+r49254) ) #1 SMP PREEMPT Mon Apr 10 21:40:48 CST 2023[ 0.000000] Boot CPU: AArch64 Processor [410fd034][ 0.000000] Ignoring memory range 0x40000000 - 0x41000000[ 0.000000] Machine: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C5[ 0.000000] efi: Getting EFI parameters from FDT:[ 0.000000] efi: UEFI not found.[ 0.000000] Reserved memory: OVERLAP DETECTED![ 0.000000] wifi_dump@51100000 (0x0000000051100000--0x0000000051700000) overlaps with wigig_dump@51300000 (0x0000000051300000--0x0000000051700000)[ 0.000000] psci: probing for conduit method from DT.[ 0.000000] psci: PSCIv1.0 detected in firmware.[ 0.000000] psci: Using standard PSCI v0.2 function IDs[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.[ 0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc03ef43000 s19328 r8192 d29824 u57344[ 0.000000] Detected VIPT I-cache on CPU0[ 0.000000] CPU features: enabling workaround for ARM erratum 845719[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 225036[ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)[ 0.000000] software IO TLB [mem 0x7fd3c000-0x7fd7c000] (0MB) mapped at [ffffffc03ed3c000-ffffffc03ed7bfff][ 0.000000] Memory: 886388K/914432K available (5258K kernel code, 609K rwdata, 2292K rodata, 220K init, 466K bss, 28044K reserved, 0K cma-reserved)[ 0.000000] Virtual kernel memory layout:[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)[ 0.000000] 0xffffffbdc0040000 - 0xffffffbdc1000000 ( 15 MB actual)[ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB)[ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB)[ 0.000000] .init : 0xffffffc0007e2000 - 0xffffffc000819000 ( 220 KB)[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0007e1844 ( 7559 KB)[ 0.000000] .data : 0xffffffc000828000 - 0xffffffc0008c0400 ( 609 KB)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1[ 0.000000] Preemptible hierarchical RCU implementation.[ 0.000000] Build-time adjustment of leaf fanout to 64.[ 0.000000] NR_IRQS:64 nr_irqs:64 0[ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns[ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns[ 0.000508] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)[ 0.000520] pid_max: default: 32768 minimum: 301[ 0.000612] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)[ 0.000622] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)[ 0.001283] EFI services will not be available.[ 0.001308] ASID allocator initialised with 65536 entries[ 0.051933] MSM Memory Dump base table set up[ 0.051954] MSM Memory Dump apps data table set up[ 0.090039] Detected VIPT I-cache on CPU1[ 0.090083] CPU1: Booted secondary processor [410fd034][ 0.120022] Detected VIPT I-cache on CPU2[ 0.120049] CPU2: Booted secondary processor [410fd034][ 0.150051] Detected VIPT I-cache on CPU3[ 0.150077] CPU3: Booted secondary processor [410fd034][ 0.150126] Brought up 4 CPUs[ 0.150153] SMP: Total of 4 processors activated.[ 0.150163] CPU: All CPU(s) started at EL1[ 0.150186] alternatives: patching kernel code[ 0.169584] DMI not present or invalid.[ 0.169818] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns[ 0.169842] futex hash table entries: 1024 (order: 5, 131072 bytes)[ 0.170038] pinctrl core: initialized pinctrl subsystem[ 0.171151] NET: Registered protocol family 16[ 0.199989] cpuidle: using governor ladder[ 0.230004] cpuidle: using governor menu[ 0.230210] NET: Registered protocol family 42[ 0.230287] vdso: 2 pages (1 code @ ffffffc00082d000, 1 data @ ffffffc00082c000)[ 0.230398] DMA: preallocated 256 KiB pool for atomic allocations[ 0.230527] CPU: IPQ8074A, SoC Version: 2.0[ 0.230949] IPC logging disabled[ 0.230955] IPC logging disabled[ 0.230960] IPC logging disabled[ 0.230964] IPC logging disabled[ 0.230969] IPC logging disabled[ 0.233206] Soc version is not 1, changing clock offsets[ 0.241895] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.244585] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.247995] sps:sps is ready.[ 0.254986] spmi spmi-0: PMIC Arb Version-2 (0x20010000)[ 0.262935] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 0.263195] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2[ 0.301899] pps_core: LinuxPPS API ver. 1 registered[ 0.301906] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>[ 0.301928] PTP clock support registered[ 0.302077] dmi: Firmware registration failed.[ 0.303583] Advanced Linux Sound Architecture Driver Initialized.[ 0.304211] clocksource: Switched to clocksource arch_sys_counter[ 0.307322] NET: Registered protocol family 2[ 0.307883] TCP established hash table entries: 8192 (order: 4, 65536 bytes)[ 0.307991] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)[ 0.308176] TCP: Hash tables configured (established 8192 bind 8192)[ 0.308228] UDP hash table entries: 512 (order: 2, 16384 bytes)[ 0.308265] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)[ 0.308437] NET: Registered protocol family 1[ 0.315795] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.315812] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.319103] Key type asymmetric registered[ 0.319118] Asymmetric key parser 'x509' registered[ 0.319146] io scheduler noop registered[ 0.319159] io scheduler deadline registered (default)[ 0.321544] 20000000.pci supply vdda not found, using dummy regulator[ 0.321590] 20000000.pci supply vdda_phy not found, using dummy regulator[ 0.321627] 20000000.pci supply vdda_refclk not found, using dummy regulator[ 0.322590] PCI host bridge /soc/pci@20000000 ranges:[ 0.322618] IO 0x20200000..0x2020ffff -> 0x20200000[ 0.322633] MEM 0x20220000..0x2fffffff -> 0x20220000[ 0.565748] qcom-pcie 20000000.pci: link up[ 0.565895] qcom-pcie 20000000.pci: PCI host bridge to bus 0000:00[ 0.565908] pci_bus 0000:00: root bus resource [bus 00-ff][ 0.565921] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x20200000-0x2020ffff])[ 0.565931] pci_bus 0000:00: root bus resource [mem 0x20220000-0x2fffffff][ 0.566250] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring[ 0.567232] pci 0000:00:00.0: BAR 8: assigned [mem 0x20300000-0x204fffff][ 0.567248] pci 0000:00:00.0: BAR 9: assigned [mem 0x20500000-0x206fffff 64bit pref][ 0.567261] pci 0000:00:00.0: BAR 0: assigned [mem 0x20220000-0x20220fff 64bit][ 0.567277] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff][ 0.567292] pci 0000:01:00.0: BAR 0: assigned [mem 0x20300000-0x20300fff 64bit][ 0.567344] pci 0000:01:00.0: BAR 2: assigned [mem 0x20301000-0x20301fff 64bit][ 0.567393] pci 0000:00:00.0: PCI bridge to [bus 01][ 0.567403] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff][ 0.567415] pci 0000:00:00.0: bridge window [mem 0x20300000-0x204fffff][ 0.567425] pci 0000:00:00.0: bridge window [mem 0x20500000-0x206fffff 64bit pref][ 0.567478] PCIe: RC0 enabled during bootup[ 0.567892] MDSS QPIC HW Base phy_Address=0x7980000 virt=ffffff80004c0000[ 0.568265] mdss_qpic_panel_probe: Panel Name = qpic lcd panel[ 0.569465] mdss_fb_register: FrameBuffer[0] 800x480 registered successfully![ 0.573296] msm_rpm_log_probe: OK[ 0.573645] msm-dcc b3000.dcc: DCC XPU is not specified[ 0.573886] msm-dcc b3000.dcc: jiffies_64: 0xffff8b08, cntvct_64: 0xb054731[ 0.573898] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80003ce004)[ 0.573909] msm-dcc b3000.dcc: gcnt_lo: 0x0b0548f9(0xffffff80003ce000)[ 0.574548] TZ SMMU State: SMMU Stage2 Enabled[ 0.574626] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set[ 0.576227] msm_serial 78b3000.serial: msm_serial: detected port #0[ 0.576265] msm_serial 78b3000.serial: uartclk = 3686400[ 0.576300] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM[ 0.576318] msm_serial: console setup on port #0[ 1.402862] console [ttyMSM0] enabled[ 1.407856] msm_serial 78b1000.serial: msm_serial: detected port #1[ 1.411123] msm_serial 78b1000.serial: uartclk = 19200000[ 1.417210] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 78, base_baud = 1200000) is a MSM[ 1.423066] msm_serial: driver initialized[ 1.431563] msm_serial_hsl_init: driver initialized[ 1.443738] brd: module loaded[ 1.444973] flash_chrdev : flash_chrdev_init [ 1.445678] flash_chrdev : flash_chrdev_init [ 1.450939] QPIC controller hw version Major:1, Minor:5[ 1.454810] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x61[ 1.459486] nand: ONFI 10-Compliant GigaDevice PSR1GA30DT[ 1.466127] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64[ 1.471456] 17 ofpart partitions found on MTD device qcom_nand.0[ 1.478855] Creating 17 MTD partitions on "qcom_nand.0":[ 1.485018] 0x000000000000-0x000000100000 : "0:SBL1"[ 1.491858] 0x000000100000-0x000000200000 : "0:MIBIB"[ 1.496731] 0x000000200000-0x000000280000 : "0:BOOTCONFIG"[ 1.501269] 0x000000280000-0x000000300000 : "0:BOOTCONFIG1"[ 1.506627] 0x000000300000-0x000000600000 : "0:QSEE"[ 1.514296] 0x000000600000-0x000000680000 : "0:DEVCFG"[ 1.517315] 0x000000680000-0x000000700000 : "0:APDP"[ 1.522237] 0x000000700000-0x000000780000 : "0:RPM"[ 1.527392] 0x000000780000-0x000000800000 : "0:CDT"[ 1.531950] 0x000000800000-0x000000980000 : "0:APPSBLENV"[ 1.537700] 0x000000980000-0x000000b80000 : "0:APPSBL"[ 1.543687] 0x000000b80000-0x000000c00000 : "0:ART"[ 1.547406] 0x000000c00000-0x000003600000 : "rootfs"[ 1.588415] mtd: device 12 (rootfs) set to be root filesystem[ 1.588737] mtdsplit: no squashfs found in "rootfs"[ 1.593137] 0x000003600000-0x000006000000 : "rootfs_1"[ 1.635136] 0x000006000000-0x000006080000 : "0:ETHPHYFW"[ 1.636185] 0x000006080000-0x000006980000 : "factory_data"[ 1.647896] 0x000006980000-0x000007a80000 : "runtime_data"[ 1.664180] libphy: Fixed MDIO Bus: probed[ 3.774917] gpio_set_value 44: 0 [1.5s~2s] gpio_set_value 44: 1[ 6.044230] gpio_set_value 37: 0 [1.5s~2s] gpio_set_value 37: 1[ 6.557237] qca-mdio 90000.mdio: Could not find phy-reset-gpio[ 6.557358] libphy: qca_mdio: probed[ 6.562715] qca-mdio 90000.mdio: qca-mdio driver was registered[ 6.565957] Unable to create IPC log context![ 6.571594] Skip QCA8074V1 in V2 platform[ 6.576124] cnss: Platform driver probed successfully. plat ffffffc03d0e2018 tgt 0xfffe[ 6.580077] i2c /dev entries driver[ 6.596177] sdhci: Secure Digital Host Controller Interface driver[ 6.596204] sdhci: Copyright(c) Pierre Ossman[ 6.601245] sdhci-pltfm: SDHCI platform and OF driver helper[ 6.606292] sdhci_msm 7824900.sdhci: sdhci_msm_probe: ICE device is not enabled[ 6.611448] sdhci_msm 7824900.sdhci: No vreg data found for vdd[ 6.618457] sdhci_msm 7824900.sdhci: No vreg data found for vdd-io[ 6.625659] sdhci_msm 7824900.sdhci: No vmmc regulator found[ 6.630586] sdhci_msm 7824900.sdhci: No vqmmc regulator found[ 6.674272] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit[ 6.694424] [ 6.694424] Version Rollback Feature Disabled[ 6.699015] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000[ 6.703233] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000[ 6.723341] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000[ 6.735184] sps:BAM 0x0000000008b04000 is registered.[ 6.745177] remoteproc remoteproc0: releasing cd00000.qcom_q6v5_wcss[ 6.748467] SPMI VADC - Min ch: 0 Max ch: 15[ 6.755698] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000[ 6.758174] coresight-csr 6001000.csr: CSR initialized[ 6.765662] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000[ 6.770582] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000[ 6.778148] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000[ 6.785507] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000[ 6.792869] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000[ 6.800268] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000[ 6.807640] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000[ 6.815045] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000[ 6.822382] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000[ 6.829781] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000[ 6.837156] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000[ 6.844536] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000[ 6.851896] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000[ 6.859292] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000[ 6.866671] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000[ 6.874032] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000[ 6.881427] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000[ 6.889021] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000[ 6.896336] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000[ 6.903747] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000[ 6.911186] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000[ 6.918525] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000[ 6.925557] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000[ 6.942659] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000[ 6.958536] sps:BAM 0x0000000006044000 is registered.[ 6.966234] coresight-tmc 6028000.tmc: TMC initialized[ 6.970994] coresight-tmc 6027000.tmc: TMC initialized[ 6.976142] coresight-funnel 6021000.funnel: FUNNEL initialized[ 6.981148] coresight-funnel 6100000.funnel: FUNNEL initialized[ 6.986984] coresight-funnel 6120000.funnel: FUNNEL initialized[ 6.992864] coresight-funnel 6130000.funnel: FUNNEL initialized[ 6.998796] coresight-funnel 61a1000.funnel: FUNNEL initialized[ 7.005280] coresight-etm4x 619c000.etm: ETM 4.0 initialized[ 7.010939] coresight-etm4x 619d000.etm: ETM 4.0 initialized[ 7.016905] coresight-etm4x 619e000.etm: ETM 4.0 initialized[ 7.022586] coresight-etm4x 619f000.etm: ETM 4.0 initialized[ 7.027818] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized[ 7.033537] coresight-stm 6002000.stm: STM initialized[ 7.042151] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000[ 7.046000] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized[ 7.054298] fan-gpio soc:fans: gpio_fan_probe success[ 7.061382] antenna-gpio soc:antennas: gpio_fan_probe success[ 7.066391] modem-gpio soc:modem: gpio_fan_probe success[ 7.074396] nf_conntrack version 0.5.0 (6924 buckets, 27696 max)[ 7.077681] ip_tables: (C) 2000-2006 Netfilter Core Team[ 7.083596] NET: Registered protocol family 10[ 7.089238] NET: Registered protocol family 17[ 7.092757] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.[ 7.097202] Bridge firewalling registered[ 7.109923] 8021q: 802.1Q VLAN Support v1.8[ 7.115365] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4[ 7.117957] pmd9655_s3: supplied by e-smps1-reg[ 7.125296] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0[ 7.129616] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1[ 7.136248] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0[ 7.143879] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable[ 7.151422] cpr3_mem_acc_init: apc: not using memory accelerator regulator[ 7.160535] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV[ 7.167480] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 808000 uV[ 7.177462] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 864000 uV[ 7.187272] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 944000 uV[ 7.197146] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 767, quot_offset[ 7]= 0[ 7.206895] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 972, quot_offset[ 7]= 205[ 7.217744] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1073, quot_offset[ 7]= 100[ 7.228682] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1226, quot_offset[ 7]= 150[ 7.239742] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop[ 7.251063] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2[ 7.257413] pmd9655_s4: supplied by e-smps1-reg[ 7.264558] cpr3_mem_acc_init: npu: not using memory accelerator regulator[ 7.268854] npu_corner: fused NOM: open-loop= 776000 uV[ 7.275808] npu_corner: fused TURBO: open-loop= 832000 uV[ 7.281649] npu_corner: fused NOM: open-loop= 776000 uV[ 7.287264] npu_corner: fused TURBO: open-loop= 832000 uV[ 7.292918] npu_corner: Normal and Cold condition init done. Default to normal.[ 7.299694] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz[ 7.305757] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz[ 7.314416] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss[ 7.321581] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available[ 7.330269] ubi0: attaching mtd12[ 7.544562] ubi0: scanning is finished[ 7.550779] ubi0: attached mtd12 (name "rootfs", size 42 MiB)[ 7.550797] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 7.555498] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 7.562262] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096[ 7.569125] ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0[ 7.575893] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128[ 7.582142] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 273099923[ 7.589180] ubi0: available PEBs: 108, total reserved PEBs: 228, PEBs reserved for bad PEB handling: 20[ 7.598127] ubi0: background thread "ubi_bgt0d" started, PID 109[ 7.619118] input: soc:gpio_keys as /devices/platform/soc/soc:gpio_keys/input/input0[ 7.619187] hctosys: unable to open rtc device (rtc0)[ 7.630753] pmd9655_ldo11: disabling[ 7.631286] ALSA device list:[ 7.634571] No soundcards found.[ 7.639610] VFS: Mounted root (squashfs filesystem) readonly on device 31:18.[ 7.640778] Freeing unused kernel memory: 220K (ffffffc0007e2000 - ffffffc000819000)[ 7.647919] Freeing alternatives memory: 40K (ffffffc000819000 - ffffffc000823000)[ 7.909292] init: Console is alive[ 7.909373] init: - watchdog -[ 7.928794] random: nonblocking pool is initialized[ 8.683951] usbcore: registered new interface driver usbfs[ 8.683992] usbcore: registered new interface driver hub[ 8.688411] usbcore: registered new device driver usb[ 8.694189] Button Hotplug driver version 0.4.1[ 8.702098] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 8.764429] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 8.826336] msm-usb-ssphy-qmp 78000.ssphy: Initializing QMP phy[ 8.833021] msm-usb-ssphy-qmp 78000.ssphy: QMP PHY initialization timeout[ 8.833042] msm-usb-ssphy-qmp 78000.ssphy: USB3_PHY_PCS_STATUS:68686868[ 9.039872] msm-usb-ssphy-qmp 58000.ssphy: Initializing QMP phy[ 9.047170] msm-usb-ssphy-qmp 58000.ssphy: QMP PHY initialization timeout[ 9.047191] msm-usb-ssphy-qmp 58000.ssphy: USB3_PHY_PCS_STATUS:68686868[ 9.253329] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.304420] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.364415] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.425595] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.484410] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.544602] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.604389] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.664780] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller[ 9.664809] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1[ 9.669281] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010[ 9.676758] xhci-hcd xhci-hcd.0.auto: irq 208, io mem 0x08a00000[ 9.685663] hub 1-0:1.0: USB hub found[ 9.691635] hub 1-0:1.0: 1 port detected[ 9.695335] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller[ 9.699269] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2[ 9.704609] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.[ 9.712304] hub 2-0:1.0: USB hub found[ 9.720456] hub 2-0:1.0: 1 port detected[ 9.724148] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller[ 9.728096] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3[ 9.733497] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010[ 9.740959] xhci-hcd xhci-hcd.1.auto: irq 209, io mem 0x08c00000[ 9.749817] hub 3-0:1.0: USB hub found[ 9.755873] hub 3-0:1.0: 1 port detected[ 9.759528] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller[ 9.763504] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4[ 9.768826] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.[ 9.776543] hub 4-0:1.0: USB hub found[ 9.784692] hub 4-0:1.0: 1 port detected[ 9.788686] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.845559] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.904405] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 9.964452] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 10.014218] usb 1-1: new high-speed USB device number 2 using xhci-hcd[ 10.912071] init: - preinit -ignore preinit load_wifi_board_binPress the [f] key and hit [enter] to enter failsafe modePress the [1], [2], [3] or [4] key and hit [enter] to select the debug levelBefore mount_rootmounting /dev/rootcp: can't stat '/tmp/log_export_tmp/*': No such file or directoryAfter mount_root[ 14.254950] procd: - early -[ 14.254987] procd: - watchdog -[ 14.878749] procd: - ubus -[ 15.880871] procd: - init -Please press Enter to activate this console.[ 15.926739] ubi1: attaching mtd15[ 15.972067] ubi1: scanning is finished[ 15.978201] ubi1: attached mtd15 (name "factory_data", size 9 MiB)[ 15.978220] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 15.983261] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 15.990131] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096[ 15.996981] ubi1: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0[ 16.003744] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128[ 16.009657] ubi1: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1097309032[ 16.016950] ubi1: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20[ 16.026245] ubi1: background thread "ubi_bgt1d" started, PID 214ubi_factory_data found, mounting...[ 16.055184] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 221[ 16.090330] UBIFS (ubi1:0): recovery needed[ 16.170166] UBIFS (ubi1:0): recovery completed[ 16.170216] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "ubi_factory_data"[ 16.173495] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes[ 16.181753] UBIFS (ubi1:0): FS size: 4825088 bytes (4 MiB, 38 LEBs), journal size 1142785 bytes (1 MiB, 9 LEBs)[ 16.191732] UBIFS (ubi1:0): reserved for root: 0 bytes (0 KiB)[ 16.201621] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 555FE482-AC27-41A3-A0C3-47CC50ED88FA, small LPT model[ 16.213139] ubi2: attaching mtd16[ 16.304218] ubi2: scanning is finished[ 16.310419] ubi2: attached mtd16 (name "runtime_data", size 17 MiB)[ 16.310439] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 16.315490] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 16.322424] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096[ 16.329287] ubi2: good PEBs: 136, bad PEBs: 0, corrupted PEBs: 0[ 16.336055] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128[ 16.342304] ubi2: max/mean erase counter: 15/8, WL threshold: 4096, image sequence number: 728371170[ 16.349342] ubi2: available PEBs: 0, total reserved PEBs: 136, PEBs reserved for bad PEB handling: 20[ 16.358637] ubi2: background thread "ubi_bgt2d" started, PID 227ubi_runtime_data found, mounting...[ 16.374436] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 234[ 16.407601] UBIFS (ubi2:0): recovery needed[ 16.496562] UBIFS (ubi2:0): recovery completed[ 16.496628] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "ubi_runtime_data"[ 16.499899] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes[ 16.508153] UBIFS (ubi2:0): FS size: 9904128 bytes (9 MiB, 78 LEBs), journal size 1777664 bytes (1 MiB, 14 LEBs)[ 16.518134] UBIFS (ubi2:0): reserved for root: 0 bytes (0 KiB)[ 16.528364] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID EB7DF1AC-F4C9-4CA1-A141-55D4B7DCC73E, small LPT model WIFI FW mount is successful[ 17.073271] use sfe_cm.ko and sfe_drv_init do nothing[ 17.081485] cfg80211: World regulatory domain updated:[ 17.081509] cfg80211: DFS Master region: unset[ 17.085535] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)[ 17.090119] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)[ 17.099823] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)[ 17.107494] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)[ 17.116861] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)[ 17.124856] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)[ 17.134573] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)[ 17.144027] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)[ 17.152105] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)[ 17.298616] ssdk_switch_device_num_init[1084]:INFO:ess-switch dts node number: 1[ 17.302311] ssdk_dt_get_switch_node[919]:INFO:ess-switch DT exist![ 17.309316] ssdk_dt_parse_access_mode[820]:INFO:switch_access_mode: local bus[ 17.315481] ssdk_dt_parse_access_mode[833]:INFO:switchreg_base_addr: 0x3a000000[ 17.322595] ssdk_dt_parse_access_mode[834]:INFO:switchreg_size: 0x1000000[ 17.329885] ssdk_dt_parse_mac_mode[288]:INFO:mac mode = 0x0[ 17.336310] ssdk_dt_parse_mac_mode[297]:INFO:mac mode1 = 0xf[ 17.341863] ssdk_dt_parse_mac_mode[306]:INFO:mac mode2 = 0xf[ 17.347519] ssdk_dt_parse_phy_info[639]:INFO:[PORT 5] port_mac_sel = QGMAC_PORT[ 17.353163] ssdk_dt_parse_uniphy[325]:INFO:ess-uniphy DT exist![ 17.360626] ssdk_plat_init start[ 17.435858] ssdk_gcc_clock_init[629]:INFO:SSDK gcc clock init successfully![ 17.438980] ssdk_probe[1923]:INFO:ess_rst doesn't exist![ 17.446092] HPPE initializing...[ 17.446964] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0xffffffff phytype doesn't match[ 17.454346] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 1, phy_id = 0xffffffff phytype doesn't match[ 17.464487] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 2, phy_id = 0xffffffff phytype doesn't match[ 17.474639] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 3, phy_id = 0xffffffff phytype doesn't match[ 17.484817] qca803x_phy_api_ops_init[2180]:INFO:qca probe qca803x phy driver succeeded![ 17.495373] qca808x_phy_api_ops_init[2155]:INFO:qca probe qca808x phy driver succeeded![ 17.504170] qca808x_ptp_register[1410]:INFO:qca808x ptp clock registered[ 17.510927] regi_init[3374]:INFO:Initializing HPPE!![ 17.734205] ssdk_ppe_reset_init[860]:INFO:ppe reset successfully![ 17.740152] qca_hppe_tdm_hw_init[674]:INFO:tdm setup num=96[ 17.743526] qca_hppe_portctrl_hw_init[105]:INFO:Hawkeye PPE port initializing[ 20.121261] ssdk_switch_register[1632]:INFO:Chip version 0x1500[ 20.124241] qca_link_polling_select[1282]:INFO:link-polling-required node does not exist[ 20.130479] ssdk_switch_register[1657]:INFO:polling is selected[ 20.138207] regi_init[3378]:INFO:Initializing HPPE Done!![ 20.143109] regi_init[3439]:INFO:qca-ssdk module init succeeded![ 20.149572] tun: Universal TUN/TAP device driver, 1.6[ 20.151576] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>[ 20.158534] EDMA ver 1 hw init[ 20.162820] EDMA HW Reset completed succesfully[ 20.165716] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)[ 20.170065] RxDesc:1 (15-15) RxFill:1 (7-7)[ 20.175793] GMAC1(ffffffc039c95880) Invalid MAC@ - using 4e:c7:5c:67:64:44[ 20.179513] libphy: PHY 90000.mdio:00 not found[ 20.186434] nss-dp: probe of 3a001000.dp1 failed with error -14[ 20.190842] GMAC2(ffffffc039c95880) Invalid MAC@ - using 92:78:26:ac:59:bc[ 20.196754] libphy: PHY 90000.mdio:01 not found[ 20.203663] nss-dp: probe of 3a001200.dp2 failed with error -14[ 20.208121] GMAC3(ffffffc039c95880) Invalid MAC@ - using c2:7a:99:cf:86:6d[ 20.214014] libphy: PHY 90000.mdio:02 not found[ 20.220946] nss-dp: probe of 3a001400.dp3 failed with error -14[ 20.225394] GMAC4(ffffffc039c95880) Invalid MAC@ - using 52:cf:f0:55:6b:32[ 20.231289] libphy: PHY 90000.mdio:03 not found[ 20.238221] nss-dp: probe of 3a001600.dp4 failed with error -14[ 20.242660] GMAC5(ffffffc039c95880) Invalid MAC@ - using 4a:0a:3c:22:81:37[ 20.450376] GMAC6(ffffffc039c9a880) Invalid MAC@ - using f6:97:bf:07:c2:59[ 20.524889] **********************************************************[ 20.524913] * NSS Data Plane driver[ 20.530293] **********************************************************[ 20.535616] l2tp_core: L2TP core driver, V2.0[ 20.540791] l2tp_netlink: L2TP netlink interface[ 20.665667] nss_driver - fw of size 743024 bytes copied to load addr: 40000000, nss_id : 0[ 20.667337] Supported Frequencies - [ 20.672813] 748.8 MHz 1.4976 GHz [ 20.678794] 1.6896 GHz [ 20.679839] [ 20.682202] ffffffbffc597100: set sdma ffffffc03ba31e00[ 20.683726] ffffffbffc597100: meminfo init succeed[ 20.717638] node size 2 # items 4[ 20.717660] memory: 40000000 1073741824 (avl 938553344) items 4 active_cores 2[ 20.719997] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000[ 20.727094] ffffffbffc597100: nss core 0 booted successfully[ 20.734777] nss_driver - fw of size 289420 bytes copied to load addr: 40800000, nss_id : 1[ 20.740574] Supported Frequencies - [ 20.747803] 748.8 MHz 1.4976 GHz [ 20.753767] 1.6896 GHz [ 20.754813] [ 20.757183] ffffffbffc59e680: set sdma ffffffc03a528a00[ 20.758705] ffffffbffc59e680: meminfo init succeed[ 20.765065] sit: IPv6 over IPv4 tunneling driver[ 20.767053] node size 2 # items 4[ 20.767056] memory: 40000000 1073741824 (avl 938553344) items 4 active_cores 2[ 20.767087] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000[ 20.767095] ffffffbffc59e680: nss core 1 booted successfully[ 20.791635] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.[ 20.800437] tipc: Activated (version 2.0.0)[ 20.804000] NET: Registered protocol family 30[ 20.808036] tipc: Started in single node mode[ 20.812841] gre: GRE over IPv4 demultiplexor driver[ 20.817518] ip_gre: GRE over IPv4 tunneling driver[ 20.822824] ip6_gre: GRE over IPv6 tunneling driver[ 20.828320] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)[ 20.843347] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 20.848091] openvswitch: Open vSwitch switching datapath[ 20.851584] QCA Hy-Fi multicast installation successfully[ 20.856953] PPP generic driver version 2.4.2[ 20.859917] nss_lag_init[354]:LAG Manager Installed[ 20.864162] NET: Registered protocol family 24[ 20.869150] PPTP driver version 0.8.5[ 20.877102] diag: IPC Logging disabled[ 20.887503] TRACK: P[0] PMask[4][ 20.887523] TRACK: P[1] PMask[4][ 20.889787] TRACK: P[2] PMask[4][ 20.895158] TRACK: P[3] PMask[4][ 20.896257] nik 4097 info->svc_id[ 20.902610] QCA multicast snooping installed successfully[ 20.903510] <NSS-CRYPTO>:module loaded Build_ID - 04/10/23, 21:12:08 SoC=ipq807x_64[ 20.911923] cannot find nss-macsec0 node[ 20.915626] cannot find nss-macsec1 node[ 20.919673] cannot find nss-macsec2 node[ 20.923553] nss_macsec init success[ 20.929554] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 20.994971] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.067009] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.154844] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.227321] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.294910] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.355276] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.414834] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.475341] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.544804] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.605119] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.664771] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.725247] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.785175] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.844737] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.905193] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 21.974781] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.035225] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.094757] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.155212] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.214776] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.274702] u32 classifier[ 22.274717] Performance counters on[ 22.276293] input device check on[ 22.280042] Actions configured[ 22.284472] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.344760] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.404792] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.465155] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.524689] Mirror/redirect action on[ 22.525251] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.584782] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.645186] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.704794] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.765253] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.824764] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.884836] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 22.945246] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.004822] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.065298] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.124822] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.185261] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.244812] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.305259] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.364810] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.425233] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.494840] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.555219] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.615253] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.674816] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.734822] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.795259] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.855261] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.914830] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 23.975257] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.034835] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.094835] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.155432] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.214884] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.275272] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.334865] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.395258] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.454861] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.515298] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.574858] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.635343] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.694854] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.755248] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.814879] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.876211] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.925030] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 24.995221] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.064959] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.125926] mhi_init Quectel_Linux_PCIE_MHI_Driver_V1.3.0.13[ 25.126051] rmnet_nss_init(): initializing rmnet_nss[ 25.130840] mhi_pci_probe pci_dev->name = 0000:01:00.0, domain=0, bus=1, slot=0, vendor=17CB, device=0306[ 25.135803] mhi_q 0000:01:00.0: BAR 0: assigned [mem 0x20300000-0x20300fff 64bit][ 25.145154] mhi_q 0000:01:00.0: enabling device (0000 -> 0002)[ 25.153910] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.215521] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.274869] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.334768] device recognition register succes[ 25.335412] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.366165] [I][mhi_netdev_enable_iface] Prepare the channels for transfer[ 25.396637] [I][mhi_netdev_enable_iface] Exited.[ 25.397025] rmnet_vnd_register_device(rmnet_mhi0.1)=0[ 25.400987] net rmnet_mhi0 rmnet_mhi0.1: NSS context created[ 25.405370] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.485089] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.545388] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.604915] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.665411] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.725312] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 25.786144] Ebtables v2.0 registered[ 25.787644] l2tp_ppp: PPPoL2TP kernel driver, V2.0[ 25.938326] Netfilter messages via NETLINK v0.30.[ 25.941881] usbcore: registered new interface driver usbserial[ 25.942038] usbcore: registered new interface driver usbserial_generic[ 25.947856] usbserial: USB Serial support registered for generic[ 25.961207] xt_time: kernel timezone is -0000[ 25.962070] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 26.047647] ctnetlink v0.93: registering with nfnetlink.[ 26.052339] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)[ 26.105538] usbcore: registered new interface driver option[ 26.105586] usbserial: USB Serial support registered for GSM modem (1-port)[ 26.110033] option 1-1:1.0: GSM modem (1-port) converter detected[ 26.117006] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0[ 26.123181] option 1-1:1.1: GSM modem (1-port) converter detected[ 26.130064] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1[ 26.136096] option 1-1:1.2: GSM modem (1-port) converter detected[ 26.142861] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2[ 26.148947] option 1-1:1.3: GSM modem (1-port) converter detected[ 26.155738] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3[ 26.162833] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of_simple)reloadprofile() beginreloadprofile() end==reloadConfig()== begin ==loadDefaultConfig()== begin ==loadConfigToFiles(): default-config to /tmp/defaultconfig== begin ==loadConfigToFiles()== end ==set_usrconfig_info()== start ==set_usrconfig_info()== end ==loadDefaultConfig()== end ==loadConfigToFiles(): user-config to /tmp/userconfig== begin ==loadConfigToFiles()== end==reloadConfig()===== no need to load emmc-config ==loadConfigToFiles(): device-config to /tmp/userconfig== begin ==loadConfigToFiles()== end ** user-config loaded **==reloadConfig()== endmerge_extra_config() begin ==loadConfigToFiles(): default-config to /tmp/merge== begin ==loadConfigToFiles()== endmergeconfigbycountry() beginmergeconfigbycountry() country USmergeconfigbycountry() endmerge_extra_config() endphylink down boot 1[ 27.491774] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready[ 27.502940] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready[ 27.715276] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not readyacfg_tool: Issuing blocking call to wait for events[ 28.479951] ECM init[ 28.480004] ECM database jhash random seed: 0x2fe6736c[ 28.482051] ECM init complete[ 28.494704] ECM OVS Test INITswitch: reset_wan_vlan: select p4: 1switch: reset_wan_vlan: select p5: 2[ 30.076407] IPv6: ADDRCONF(NETDEV_UP): br-wan: link is not ready[ 30.122680] Load statistics in Router Mode[ 30.122763] module initedto down eth0/1 after netfid[ 30.296120] ext_antenna_en_store ==>gpio 56 value 0 buf 0[ 30.296120] [awnd_update_wifi_tpie:911]: config_generic failed awnd_update_tpie(): ath02[-1] [awnd_update_wifi_tpie:911]: config_generic failed awnd_update_tpie(): ath12[-1] apsd: start apsdwhc (repacd): Start:whc (repacd): GatewayConnectedMode(gwcon_mode): CAPwhc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1whc (repacd): get whc_wifi_config_lockwhc (repacd): starting WHC auto-configurationwhc (repacd): Managed network: lanwhc (repacd): Device type: APwhc (repacd): Sysmode: Routerwhc (repacd): the guest network version of the device is latest, we do nothing(uci_revert_state wifi guest enable)whc (repacd): stop repacd-run.shwhc (repacd): Start:whc (repacd): GatewayConnectedMode(gwcon_mode): CAPwhc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1whc (repacd): wifi config change(is different from /var/state/wifi). wifi_cmd:reload wifi1,wifi0whc (repacd): Using SON mode for GW Connected APwhc (repacd): __repacd_restart_dependencies: Restarting network stack...wifi reload[ 32.429779] IPv6: ADDRCONF(NETDEV_UP): br-wan: link is not ready[ 32.431707] [I][mhi_netdev_open] Opened net dev interface[ 32.435036] IPv6: ADDRCONF(NETDEV_UP): rmnet_mhi0: link is not ready[ 32.441973] 8021q: VLANs not supported on rmnet_mhi0[ 32.446890] IPv6: ADDRCONF(NETDEV_UP): rmnet_mhi0.1: link is not ready[ 32.455784] device eth0 entered promiscuous mode[ 32.458065] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready[ 32.465207] device eth1 entered promiscuous mode[ vlan_set_device_state ] 165: --------------->Create VID='1' qcawifi qcawificfg80211 disable radio wifi1qcawifi qcawificfg80211 disable radio wifi0qcawifi qcawificfg80211 disable radio wifi2qcawifi qcawificfg80211: enable radio wifi1echo -n /ini > /sys/module/firmware_class/parameters/pathupdate_ini_file cfg80211_config=1update_ini_file qwrap_enable=0update_ini_file nss_wifi_olcfg=3update_ini_file rx_hash=0sysctl -w dev.nss.n2hcfg.extra_pbuf_core0=9000000[ 33.534121] configuring additional NSS pbufs[ 33.560538] additional pbufs of size 9003008 got added to NSSsysctl -w dev.nss.n2hcfg.n2h_high_water_core0=67392sysctl -w dev.nss.n2hcfg.n2h_wifi_pool_buf=40960insmod mem_manager[ 33.584124] mem_manager: module license 'Proprietary' taints kernel.[ 33.584152] Disabling lock debugging due to kernel taintinsmod qdf mem_debug_disabled=1insmod asfinsmod umac enable_pktlog_support=1[ 33.952252] wlan: [2582:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50insmod qca_spectralecho 1 > /sys/module/cnss2/parameters/cold_boot_supportecho 1 > /sys/module/cnss2/parameters/daemon_support*****starting cnssdaemon**************initiating cold boot calibration*************insmod qca_ol testmode=7echo -1000 > /proc/`pgrep cnssdaemon`/oom_score_adj*****cnssdaemon pid=2617*********insmod wifi_3_0[ 34.210926] wlan: [2623:I:ANY] =======ol_if_register_wifi3_0==========[ 34.210926] [ 34.210962] wlan: [2623:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd649a40[ 34.217870] wlan: [2623:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 2 bus_type 1[ 34.229930] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss[ 34.248883] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668[ 35.215357] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up[ 35.215421] wlan: [2623:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 3 bus_type 1[ 35.215824] rpmsg_dev_probe: No pm domain[ 35.215975] rpmsg_dev_probe: No pm domain[ 35.216853] cnss: QMI WLFW service connected, state: 0x1[ 35.216998] cnss: device_id : 65534 mem mode : [0][ 35.217086] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffffbffc9dacc8[ 35.218749] cnss: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x220604a5, fw_build_timestamp: 2021-08-12 01:51, otp_version: 0x0 eeprom_caldata_read_timeout 0s[ 35.218757] cnss: Downloading BDF: bdwlan.bin, size: 64[ 35.218762] cnss: No board_id entry in device tree[ 35.219162] cnss: BDF location : 0x4b0c0000[ 35.219167] cnss: BDF IPQ8074/bdwlan.bin size 131072[ 35.219382] cnss: Downloading BDF: caldata.bin, size: 64[ 35.219801] cnss: per device BDF location : 0x4b0e0000[ 35.219886] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000[ 35.306486] wlan: [2623:I:ANY] ol_ath_check_fw_ready: 614: Waiting for FW ready device fffe[ 35.313326] wlan: [2623:I:ANY] ol_ath_check_fw_ready: 624: FW ready received for device fffe[ 35.322423] wlan: [2623:I:ANY] pld_ahb_wlan_enable: 691: cnss_mode: Cold boot calibration[ 35.406828] wlan: [2623:I:ANY] Coldboot calibration wait started[ 35.406828] not found in configecho 0 to init===parental_control_avira=== no need to start[ 36.186999] mode:0[ 3366(lan)] [smartip_get_cfg 166] key:gw value:192.168.68.1 [ 3366(lan)] [smartip_get_cfg 166] key:lanip value:192.168.68.1 [ 3366(lan)] [smartip_get_cfg 166] key:lantype value:1 GMT-12:00 [ 3366(lan)] [smartip_get_cfg 166] key:mask value:255.255.252.0 false 0[ 3366(lan)] [smartip_init_dhcp_hook_socket 2329] create dhcp ho[ 36.757355] g_back_dev_num:16ok success [ 3366(lan)] [smartip_start_drop_dhcp_pkg 2215] start select dhcp package! [ 3366(lan)] [smartip_check_status_Router_mode 1719] new dnsServer is 0xc0a84401 0x0 [ 3366(lan)] [smartip_notify_lan_update 1320] Notify the lan ip changed. [ 3366(lan)] [smartip_update_lanip 593] config IP: ifconfig br-lan 192.168.68.1 netmask 255.255.252.0 [ 3366(lan)] [smartip_update_lanip 604] route del default dev br-lan [ 3366(lan)] [smartip_update_lanip 622] restart miniupnpd [ 3623(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:UPDATE [ 3669(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:FAPIPUPDATE IPConflict2 mask:22 lan_addr:192.168.68.1 mask_str:255.255.252.0IPConflict2 mask:22IPConflict2 old_mask:255.255.252.0 old_ip:192.168.68.1[ 37.027652] mode:0[ 3366(lan)] [smartip_update_lanip 634] restart domain_login [ 3366(lan)] [smartip_start_process 366] start udhcpd [ 38.566713] Ebtables v2.0 unregistered[ flowstat_get_wwan_tx_rx_statistics ] 136: Get Rx/Tx flow from qmi failed! [ 41.107046] wlan: [2623:I:ANY] Coldboot calibration wait ended[ 41.107046] [ 41.108717] wlan: [2623:I:ANY] ol_ath_do_cold_boot_calibration: 598: Coldboot calib successful: radio_id 0x65534[ 41.108777] cnss: QMI WLFW service disconnected, state: 0x6[ 41.124118] wlan: [2623:I:ANY] init_ath_pci_3_0: 179: 6ath_ol_pci_wifi3.0 : (Atheros/multi-bss)[ 41.134504] wlan: [3807:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 0 bus_type 1rmmod wifi_3_0[ 41.163768] remoteproc remoteproc0: stopped remote processor cd00000.qcom_q6v5_wcss[ 41.163817] wlan: [3807:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 1 bus_type 1rmmod qca_olinsmod qca_olinsmod wifi_3_0[ 41.299397] wlan: [3815:I:ANY] =======ol_if_register_wifi3_0==========[ 41.299397] [ 41.299433] wlan: [3815:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd897a40[ 41.306266] wlan: [3815:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 2 bus_type 1[ 41.318385] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss[ 41.327102] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668[ 41.684235] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up[ 41.684303] wlan: [3815:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 3 bus_type 1[ 41.684685] rpmsg_dev_probe: No pm domain[ 41.684857] rpmsg_dev_probe: No pm domain[ 41.685472] cnss: QMI WLFW service connected, state: 0x1[ 41.685628] cnss: device_id : 65534 mem mode : [0][ 41.695764] cnss: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x220604a5, fw_build_timestamp: 2021-08-12 01:51, otp_version: 0x0 eeprom_caldata_read_timeout 0s[ 41.695772] cnss: Downloading BDF: bdwlan.bin, size: 64[ 41.695777] cnss: No board_id entry in device tree[ 41.696164] cnss: BDF location : 0x4b0c0000[ 41.696165] cnss: BDF IPQ8074/bdwlan.bin size 131072[ 41.696392] cnss: Downloading BDF: caldata.bin, size: 64[ 41.696749] cnss: per device BDF location : 0x4b0e0000[ 41.696846] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000[ 41.765976] wlan: [3815:I:ANY] ol_ath_check_fw_ready: 614: Waiting for FW ready device fffe[ 41.772814] wlan: [3815:I:ANY] ol_ath_check_fw_ready: 624: FW ready received for device fffe[ 41.781514] wlan: [3815:I:ANY] pld_ahb_wlan_enable: 699: cnss_mode: Mission mode [ 41.798345] wlan: [3815:I:ANY] qca_napi_create: 364: qca_napi_create: napi instance 0 created on pipe 4[ 41.798532] wlan: [3815:I:ANY] __ol_ath_attach: 3922: Allocated soc ffffffc031180880[ 41.824310] wlan: [3815:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_tx=1000 - Out of range [8, 100]; Using 1000[ 41.824438] wlan: [3815:E:CONFIG] cfg_uint_item_handler: 171: dp_rxdma_monitor_buf_ring=8192 - Out of range [16, 4096]; Using 2048[ 41.834959] wlan: [3815:E:CONFIG] cfg_uint_item_handler: 171: dp_rxdma_monitor_dst_ring=8192 - Out of range [48, 4096]; Using 1024[ 41.846666] wlan: [3815:I:ANY] osif_nss_wifi_soc_setup: 170: nss-wifili: Could not set nss_cfg due to Invalid HW mode 7[ 41.858212] wlan: [3815:I:ANY] osif_nss_wifi_soc_setup: 204: nss register id -1 nss config 3 Target Type 18 [ 41.868902] wlan: [3815:I:ANY] __ol_ath_attach: 4129: dev name soc0[ 41.879110] wlan: [3815:I:ANY] ol_ath_soc_attach: 7124: WMI attached. wmi_handle ffffffc034e57400 [ 41.885027] wlan: [3815:I:ANY] htc_wmi_init: 6134: htc_wmi_init() HT Create . ffffffc0338dc000[ 41.893964] wlan: [3815:I:ANY] htc_wmi_init: 6141: htc_wmi_init() Skipping BMI Done. [ 41.902564] wlan: [3815:I:ANY] htc_wmi_init: 6198: [htc_wmi_init:6198] host_enable 0 nss_nwifi_offload 0[ 41.913048] wlan: [3815:I:ANY] ol_target_init_complete: 6320: CDP soc attach success[ 41.920020] wlan: [3815:I:ANY] ol_target_init_complete: 6327: Soc attach success NSS config 0 [ 41.927781] wlan: [3815:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc0338dc000, ep 2, value 1[ 41.936197] wlan: [3815:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc0338dc000, ep 3, value 1[ 41.946526] wlan: [3815:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc0338dc000, ep 4, value 1[ 41.957172] wlan: [485:I:TIF] init_deinit_populate_hw_mode_capability: 361: Preferred mode is not set, use mode id 1[ 41.957172] [ 41.967159] wlan: [485:I:TIF] HE_CAP Info = 1a08010d[ 41.979207] wlan: [485:I:TIF] Num HW modes = 1[ 41.984237] wlan: [485:I:TIF] Num PHY = 2[ 41.988490] wlan: [485:I:TIF] Preferred HW Mode = 1 Num Radios = 2[ 41.992574] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes,[ 41.998656] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 0 wireless modes = f97f9001[ 42.007251] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes,[ 42.016451] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 1 wireless modes = 680680c[ 42.024960] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 0 wireless modes = f97f9001[ 42.034159] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 1 wireless modes = 680688c[ 42.044582] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 421: dfs_offload 1[ 42.054740] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2850: dfs->dfs_psoc_idx: 0 [ 42.064718] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2856: dfs_soc_obj->num_dfs_privs: 1 [ 42.074643] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 393: Do not allocate DFS object for 2G, pdev_id = 1[ 42.084728] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:0 wmi_handle:ffffffc034e57400[ 42.126670] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 0 Number of peers = 529 vdevs = 17[ 42.126707] wlan: [485:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success[ 42.135855] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:1 wmi_handle:ffffffc034d11c00[ 42.152559] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 1 Number of peers = 529 vdevs = 17[ 42.153795] wlan: [485:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success[ 42.264304] wlan: [485:I:ANY] copy_fw_abi_version_tlv: 6960: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0[ 42.463769] wlan: [485:I:ANY] ready_extract_init_status_tlv: 9002: ready_extract_init_status_tlv:0[ 42.463799] wlan: [485:I:ANY] dp_peer_map_attach_wifi3: 9790: dp_peer_map_attach_wifi3 max_peers 1109, max_ast_index: 4112[ 42.463799] [ 42.471815] wlan: [3815:I:ANY] ol_ath_connect_htc: 1215: WMI is ready[ 42.484179] wlan: [3815:I:ANY] ol_ath_soc_attach: 7215: connect HTC[ 42.490628] wlan: [3815:I:ANY] ol_ath_soc_attach: 7216: bypasswmi : 0[ 42.496716] wlan: [3815:I:ANY] ol_ath_soc_attach: 7290: ol_ath_soc_attach() UMAC attach . [ 42.503355] wlan: [3815:I:ANY] __ol_ath_attach: 4242: pdev_netdev name wifi0[ 42.511468] wlan: [3815:I:ANY] __ol_ath_attach: 4289: Skip txrx_pdev_attach_target[ 42.518666] wlan: [3815:I:ANY] __ol_ath_attach: 4315: BURSTING enabled by default[ 42.526092] wlan: [3815:I:ANY] ol_ath_pdev_attach: 9058: interface_id 0[ 42.533595] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7444: phy id = 0 Modes supported[ 42.540022] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7451: 11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1[ 42.548359] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7460: Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4900, hi_5g = 6100[ 42.558611] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1344: wireless_modes = f97f9001 before update[ 42.572921] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1359: Wireless_modes = f97f9001 after update[ 42.582660] wlan: [3815:I:ANY] ol_ath_update_ext_caps: 1932: 11ax 5G supported case[ 42.592374] wlan: [3815:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed[ 42.599863] wlan: [3815:I:ANY] acfg_attach: 3519: acfg_attach: 3519: Netlink socket created:ffffffc02b620400[ 42.606350] wlan: [3815:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1[ 42.616734] wlan: [3815:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 4[ 42.623799] wlan: [0:I:ANY] ol_ath_pdev_attach: 9402: Set global_ic[1], ptr:ffffffbffd3721e8[ 42.630821] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d12008) Enabling DBDC Repeater 1 [ 42.639503] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(ffffffc034d12008) is_primary 1 [ 42.648838] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14623: twt enabled.[ 42.648838] [ 42.650024] wlan: [3815:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 542: cfg block channel list is empty[ 42.650029] wlan: [3815:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3850: pdev_idx = 0 tx_desc_limit = 0[ 42.650043] wlan: [3815:I:ANY] osif_wrap_attach: 239: osif wrap attached[ 42.650043] [ 42.650045] wlan: [3815:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done[ 42.650045] [ 42.650049] wlan: [3815:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc02b620800 ic->ic_wrap_com=ffffffc02b620800 &wrap_com->wc_devt=ffffffc02b620800 [ 42.650049] [ 42.650069] wlan: [3815:I:ANY] __ol_ath_attach: 4485: needed_headroom reservation 60[ 42.650245] wlan: [3815:I:ANY] ieee80211_cfg80211_radio_attach: 11806: ic: 0xffffffc030f60880, wdev: 0xffffffc030f78a58, wiphy: 0xffffffc0320442a0, netdev: 0xffffffc030f60000 [ 42.650707] wlan: [3815:I:ANY] __ol_ath_attach: 4242: pdev_netdev name wifi1[ 42.650722] wlan: [3815:I:ANY] __ol_ath_attach: 4289: Skip txrx_pdev_attach_target[ 42.650725] wlan: [3815:I:ANY] __ol_ath_attach: 4315: BURSTING enabled by default[ 42.650763] wlan: [3815:I:ANY] ol_ath_pdev_attach: 9058: interface_id 1[ 42.650774] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7444: phy id = 1 Modes supported[ 42.650778] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7451: 11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1[ 42.650782] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7460: Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0[ 42.650785] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1344: wireless_modes = 680680c before update[ 42.650787] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1359: Wireless_modes = 680680c after update[ 42.650791] wlan: [3815:I:ANY] ol_ath_update_ext_caps: 1940: 11ax 2G supported case[ 42.650882] wlan: [3815:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed[ 42.650988] wlan: [3815:I:ANY] acfg_attach: 3494: Offload using existing sock ffffffc02b620400[ 42.650997] wlan: [3815:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1[ 42.651164] wlan: [3815:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 11[ 42.651188] wlan: [0:I:ANY] ol_ath_pdev_attach: 9402: Set global_ic[2], ptr:ffffffbffd3721e8[ 42.651193] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d11808) Enabling DBDC Repeater 1 [ 42.651198] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(ffffffc034d11808) is_primary 0 [ 42.652581] wlan: [3815:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 542: cfg block channel list is empty[ 42.652586] wlan: [3815:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3850: pdev_idx = 1 tx_desc_limit = 0[ 42.652600] wlan: [3815:I:ANY] osif_wrap_attach: 239: osif wrap attached[ 42.652600] [ 42.652603] wlan: [3815:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done[ 42.652603] [ 42.652607] wlan: [3815:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc02b622400 ic->ic_wrap_com=ffffffc02b622400 &wrap_com->wc_devt=ffffffc02b622400 [ 42.652607] [ 42.652622] wlan: [3815:I:ANY] __ol_ath_attach: 4485: needed_headroom reservation 60[ 42.652634] wlan: [3815:I:ANY] wlan_cfg80211_init: 11680: Number of 2G channels: 11 [ 42.652746] wlan: [3815:I:ANY] ieee80211_cfg80211_radio_attach: 11806: ic: 0xffffffc030fa0880, wdev: 0xffffffc030fb8a58, wiphy: 0xffffffc034ff5aa0, netdev: 0xffffffc030fa0000 [ 42.653112] wlan: [3815:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3819: Running with HW mode = 1[ 42.653305] wlan: [3815:E:QLD] qld_register: 108: Handle or address is NULL[ 42.653318] wlan: [3815:I:ANY] wlan_pdev_operation: 726: num_radios=1, wifi_radios[0].sc = ffffffc030f60880_radio_type = 2[ 42.653322] wlan: [3815:I:ANY] wlan_pdev_operation: 726: num_radios=2, wifi_radios[1].sc = ffffffc030fa0880_radio_type = 2[ 42.653344] wlan: [3815:I:ANY] init_ath_pci_3_0: 179: 6ath_ol_pci_wifi3.0 : (Atheros/multi-bss)[ 43.011809] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14623: twt enabled.[ 43.011809] insmod wifi_2_0[ 43.033399] wlan: [3820:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd938de0[ 43.033842] wlan: [3820:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0: (Atheros/multi-bss)insmod ath_pktloginsmod smart_antennaQCAWIFICFG80211 No Direct-Attach chipsets found.cfg80211tool wifi1 setCountry US[ 43.662756] wlan: [4231:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 11[ 43.662830] wlan: [4231:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0[ 43.669238] wlan: [4231:I:ANY] wlan_cfg80211_set_country: 6519: wlan_cfg80211_set_country: Country: US ret: 0 cfg80211tool wifi1 bsta_fixed_idmask 255cfg80211tool wifi1 set_bcnburst 1cfg80211tool wifi1 ce_debug_stats 1cfg80211tool wifi1 sIgmpDscpOvrid 1cfg80211tool wifi1 sIgmpDscpTidMap 6cfg80211tool wifi1 enable_ol_stats 1[ 43.809245] wlan: [4249:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max_mac_rings 1 [ 43.809313] wlan: [4249:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max_mac_rings 1 ifconfig wifi1 down[ flowstat_get_wwan_tx_rx_statistics ] 136: Get Rx/Tx flow from qmi failed! cfg80211tool wifi1 setHwaddr B4:B0:24:59:B8:0E[ 43.842525] wlan: [4255:I:ANY] wlan_cfg80211_set_hwaddr: 6592: wlan_cfg80211_set_hwaddr :b4:b0:24:59:b8:0e ret: 0 ifconfig wifi1 upcfg80211tool wifi1 txbf_snd_int 100[ 43.871625] wlan: [4260:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: value 100 wmi_status 0cfg80211tool wifi1 obss_rssi_th 35cfg80211tool wifi1 obss_rxrssi_th 35cfg80211tool wifi1 dbdc_enable 0[ 43.942217] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d11808) Enabling DBDC Repeater 0 cfg80211tool wifi1 no_vlan 1cfg80211tool wifi1 discon_time 10[ 43.992196] wlan: [0:I:ANY] ol_ath_set_config_param: 2377: Disconnect_timeout value: 10cfg80211tool wifi1 reconfig_time 60[ 44.017214] wlan: [0:I:ANY] ol_ath_set_config_param: 2383: Reconfiguration_timeout value:60sysctl -w dev.nss.n2hcfg.n2h_high_water_core0=67392sysctl -w dev.nss.n2hcfg.n2h_wifi_pool_buf=40960cfg80211tool wifi1 fc_buf0_max 16384cfg80211tool wifi1 fc_buf1_max 16384cfg80211tool wifi1 fc_buf2_max 16384cfg80211tool wifi1 fc_buf3_max 32768sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core0=256sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core1=256cfg80211tool wifi1 get_rxchainmasknumber of vifs: ath0 ath02 ifconfig wifi1 upwlanconfig ath0 create wlandev wifi1 wlanmode ap -cfg80211iw phy phy1 interface add ath0 type __ap[ 44.328604] wlan: [4382:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath0 : clone params: 0x00000001 [ 44.328677] wlan: [4382:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create b4:b0:24:59:b8:0e[ 44.339697] wlan: [4382:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030fa0880, opmode=IEEE80211_M_HOSTAP, flags=0x1[ 44.339697] [ 44.347991] wlan: [4382:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1[ 44.360190] wlan: [4382:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0[ 44.367305] wlan: [4382:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b[ 44.382590] wlan: [4382:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged[ 44.389377] wlan: [4382:I:ANY] MBO Initialized[ 44.403391] wlan: [4382:I:ANY] OCE Initialized[ 44.407926] wlan: [4382:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO:1|LRO:0[ 44.413312] wlan: [4382:I:ANY] VAP device ath0 created osifp: (ffffffc02d12a880) os_if: (ffffffc02a9d0000)cfg80211tool ath0 mode 11GHE40cfg80211tool ath0 mode 11GHE40cfg80211tool ath0 channel 0cfg80211tool ath0 hide_ssid 0cfg80211tool ath0 nrshareflag 7cfg80211tool ath0 disablecoext 1iw ath0 set 4addr oncfg80211tool ath0 wds 1cfg80211tool ath0 backhaul 0cfg80211tool ath0 uapsd 1cfg80211tool ath0 vap_ind 0cfg80211tool ath0 extap 0iw ath0 set 4addr oncfg80211tool ath0 stafwd 0cfg80211tool ath0 maxsta 128[ 44.874157] wlan: [4446:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128cfg80211tool ath0 blockdfschan 1cfg80211tool ath0 twt_responder 0cfg80211tool ath0 rrm 1cfg80211tool ath0 vhtsubfee 1cfg80211tool ath0 vhtmubfee 1cfg80211tool ath0 vhtsubfer 1cfg80211tool ath0 vhtmubfer 1cfg80211tool ath0 he_subfee 1[ 45.181418] wlan: [4473:I:ANY] wlan_set_param: 2964: HE SU BFEE already set with this value =1 cfg80211tool ath0 he_subfer 1[ 45.223138] wlan: [4476:I:ANY] wlan_set_param: 2983: HE SU BFER already set with this value =1 cfg80211tool ath0 he_mubfee 1[ 45.264096] wlan: [4479:I:ANY] ieee80211_ucfg_setparam: 4919: HE MU BFEE only supported in STA mode cfg80211tool ath0 he_mubfer 1[ 45.305871] wlan: [4482:I:ANY] wlan_set_param: 3029: HE MU BFER already set with this value =1 cfg80211tool ath0 athnewind 1iwpriv ath0 he_ulmumimo 0[ 45.364080] wlan: [4493:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0|dl_muofdma_bfer:0[ 45.364126] wlan: [4493:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x3biwpriv ath0 he_ulofdma 0[ 45.385664] wlan: [4496:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:0|ul_mumimo:0|dl_muofdma_bfer:0[ 45.387245] wlan: [4496:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x1bcfg80211tool ath0 ap_bridge 1wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath0:/var/run/hostapd-ath0.conf[ 45.554826] device ath0 entered promiscuous mode[ 45.555292] br-lan: port 3(ath0) entered forwarding state[ 45.560034] br-lan: port 3(ath0) entered forwarding state[ 45.565933] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-0(ath0):ACS Params[ 45.570707] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:29|chwidth:20|[ 45.578243] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS started: vap:0xffffffc02a9d0000[ 45.589234] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes readyifconfig ath0 upiw phy phy1 set rts offwlanconfig ath02 create wlandev wifi1 wlanmode ap -cfg80211iw phy phy1 interface add ath02 type __ap[ 45.728033] wlan: [4572:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath02 : clone params: 0x00000001 [ 45.728099] wlan: [4572:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create ba:b0:24:59:b8:0e[ 45.739063] wlan: [4572:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030fa0880, opmode=IEEE80211_M_HOSTAP, flags=0x1[ 45.739063] [ 45.747471] wlan: [4572:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1[ 45.759699] wlan: [4572:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0[ 45.766810] wlan: [4572:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b[ 45.782172] wlan: [4572:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged[ 45.788883] wlan: [4572:I:ANY] MBO Initialized[ 45.802897] wlan: [4572:I:ANY] OCE Initialized[ 45.807438] wlan: [4572:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO:1|LRO:0[ 45.812772] wlan: [4572:I:ANY] VAP device ath02 created osifp: (ffffffc02d12c880) os_if: (ffffffc02a480000)cfg80211tool ath02 mode 11GHE40cfg80211tool ath02 mode 11GHE40cfg80211tool ath02 channel 0cfg80211tool ath02 hide_ssid 1cfg80211tool ath02 dynamicbeacon 0cfg80211tool ath02 disablecoext 1iw ath02 set 4addr oncfg80211tool ath02 wds 1cfg80211tool ath02 backhaul 0cfg80211tool ath02 uapsd 1cfg80211tool ath02 vap_ind 0cfg80211tool ath02 extap 0iw ath02 set 4addr oncfg80211tool ath02 stafwd 0cfg80211tool ath02 maxsta 128[ 46.269705] wlan: [4635:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128cfg80211tool ath02 blockdfschan 1cfg80211tool ath02 twt_responder 0cfg80211tool ath02 rrm 1cfg80211tool ath02 athnewind 1cfg80211tool ath02 rept_spl 0cfg80211tool ath02 ap_bridge 1wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath02:/var/run/hostapd-ath02.conf[ 46.643233] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-1(ath02):ACS Params[ 46.643394] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:29|chwidth:20|[ 46.650864] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS started: vap:0xffffffc02a480000ifconfig ath02 upiw phy phy1 set rts offqcawifi qcawificfg80211: enable radio wifi0echo -n /ini > /sys/module/firmware_class/parameters/pathupdate_ini_file cfg80211_config=1update_ini_file qwrap_enable=0update_ini_file nss_wifi_olcfg=3update_ini_file rx_hash=0cfg80211tool wifi0 blockdfslist 1cfg80211tool wifi0 setCountry US[ 47.380336] wlan: [5236:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 4[ 47.380792] wlan: [5236:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 4[ 47.386497] wlan: [5236:I:ANY] number of channels: 2G = 0 5G = 4, 6G = 0[ 47.393745] wlan: [5236:I:ANY] wlan_cfg80211_set_country: 6519: wlan_cfg80211_set_country: Country: US ret: 0 [ 47.400733] wlan: [941:I:ANY] ol_acfg_handle_wifi_ioctl: 446: ol_acfg_handle_wifi_ioctl: req->cmd=76 not valid for radio interface, it's for VAPcfg80211tool wifi0 bsta_fixed_idmask 255cfg80211tool wifi0 set_bcnburst 1cfg80211tool wifi0 ce_debug_stats 1cfg80211tool wifi0 sIgmpDscpOvrid 1cfg80211tool wifi0 sIgmpDscpTidMap 6cfg80211tool wifi0 enable_ol_stats 1[ 47.544745] wlan: [5254:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max_mac_rings 1 [ 47.544810] wlan: [5254:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max_mac_rings 1 ifconfig wifi0 downcfg80211tool wifi0 setHwaddr B4:B0:24:59:B8:0F[ 47.577762] wlan: [5259:I:ANY] wlan_cfg80211_set_hwaddr: 6592: wlan_cfg80211_set_hwaddr :b4:b0:24:59:b8:0f ret: 0 ifconfig wifi0 upcfg80211tool wifi0 txbf_snd_int 100[ 47.606606] wlan: [5264:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: value 100 wmi_status 0cfg80211tool wifi0 obss_rssi_th 35cfg80211tool wifi0 obss_rxrssi_th 35cfg80211tool wifi0 dbdc_enable 0[ 47.677158] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d12008) Enabling DBDC Repeater 0 cfg80211tool wifi0 no_vlan 1cfg80211tool wifi0 discon_time 10[ 47.727734] wlan: [0:I:ANY] ol_ath_set_config_param: 2377: Disconnect_timeout value: 10cfg80211tool wifi0 reconfig_time 60[ 47.752684] wlan: [0:I:ANY] ol_ath_set_config_param: 2383: Reconfiguration_timeout value:60cfg80211tool wifi0 fc_buf0_max 32768cfg80211tool wifi0 fc_buf1_max 32768cfg80211tool wifi0 fc_buf2_max 32768cfg80211tool wifi0 fc_buf3_max 32768sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core0=256sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core1=256cfg80211tool wifi0 get_rxchainmasknumber of vifs: ath1 ath12 ifconfig wifi0 upwlanconfig ath1 create wlandev wifi0 wlanmode ap -cfg80211iw phy phy0 interface add ath1 type __ap[ 47.999653] wlan: [5377:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath1 : clone params: 0x00000001 [ 47.999719] wlan: [5377:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create b4:b0:24:59:b8:0f[ 48.010682] wlan: [5377:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030f60880, opmode=IEEE80211_M_HOSTAP, flags=0x1[ 48.010682] [ 48.019026] wlan: [5377:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1[ 48.031266] wlan: [5377:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0[ 48.038337] wlan: [5377:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b[ 48.053656] wlan: [5377:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged[ 48.060423] wlan: [5377:I:ANY] MBO Initialized[ 48.074431] wlan: [5377:I:ANY] OCE Initialized[ 48.078971] wlan: [5377:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO:1|LRO:0[ 48.084652] wlan: [5377:I:ANY] VAP device ath1 created osifp: (ffffffc02b302880) os_if: (ffffffc02a4a8000)cfg80211tool ath1 mode 11AHE80cfg80211tool ath1 mode 11AHE80cfg80211tool ath1 channel 0cfg80211tool ath1 hide_ssid 0cfg80211tool ath1 nrshareflag 7cfg80211tool ath1 disablecoext 1iw ath1 set 4addr oncfg80211tool ath1 wds 1cfg80211tool ath1 backhaul 0cfg80211tool ath1 uapsd 1cfg80211tool ath1 vap_ind 0cfg80211tool ath1 extap 0iw ath1 set 4addr oncfg80211tool ath1 amsdu 2cfg80211tool ath1 stafwd 0cfg80211tool ath1 maxsta 128[ 48.577306] wlan: [5445:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128cfg80211tool ath1 blockdfschan 1cfg80211tool ath1 twt_responder 0cfg80211tool ath1 rrm 1cfg80211tool ath1 vhtsubfee 1cfg80211tool ath1 vhtmubfee 1cfg80211tool ath1 vhtsubfer 1cfg80211tool ath1 vhtmubfer 1[ flowstat_get_wwan_tx_rx_statistics ] 136: Get Rx/Tx flow from qmi failed! cfg80211tool ath1 he_subfee 1[ 48.884830] wlan: [5472:I:ANY] wlan_set_param: 2964: HE SU BFEE already set with this value =1 cfg80211tool ath1 he_subfer 1[ 48.926217] wlan: [5475:I:ANY] wlan_set_param: 2983: HE SU BFER already set with this value =1 cfg80211tool ath1 he_mubfee 1[ 48.967891] wlan: [5478:I:ANY] ieee80211_ucfg_setparam: 4919: HE MU BFEE only supported in STA mode cfg80211tool ath1 he_mubfer 1[ 48.980674] ieee80211_acs_find_best_11ng_centerchan: acs_11ngbestchan = 11[ 48.980704] 2.4G Best Channel Selected 10 rssi 0 nf -97 [ 48.986628] wlan: [2583:I:ANY] vap-0(ath0): ACS result PCH 10 freq 2457, SCH 6 freq 2437, hw_mode 1 chwidth 40, vht_seg0 8 freq 2447, vht_seg1 0 freq 0[ 48.991906] wlan: [2583:I:ANY] vap-1(ath02): ACS result PCH 10 freq 2457, SCH 6 freq 2437, hw_mode 1 chwidth 40, vht_seg0 8 freq 2447, vht_seg1 0 freq 0[ 49.005414] wlan: [2583:I:ANY] ieee80211_acs_scan_evhandler: 3885: lock held duration: 25(ms)[ 49.023510] wlan: [5481:I:ANY] wlan_set_param: 3029: HE MU BFER already set with this value =1 [ 49.027754] wlan: [954:I:ANY] DES SSID SET=deco[ 49.036448] wlan: [954:I:ANY] wlan_cfg80211_chan_to_phymode: 1239: wlan_cfg80211_chan_to_phymode: band:0 width: 2 channel_cfreq: 2457 center_freq1: 2447 chandef.center_freq2: 0 flags: 0 [ 49.040808] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 49.040808] Channel is configured already!!cfg80211tool ath1 athnewind 1[ 49.082772] wlan: [0:I:CMN_MLME] vdev[0] ieee chan:10 freq:2457[ 49.082984] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 49.082984] FD Interval should be a factor of BI.[ 49.082984] Disabling FD[ 49.082984] [ 49.087606] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 49.087606] FD Interval should be a factor of BI.[ 49.087606] Disabling FD[ 49.087606] [ 49.094846] wlan: [954:I:ANY] DES SSID SET=zEQQkhpPcoaHsP34[ 49.094851] wlan: [954:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 27[ 49.094902] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 49.094902] Channel is configured already!![ 49.140523] wlan: [0:I:ANY] vdev[0]: Mgt Rate:1000(kbps)[ 49.151148] wlan: [0:I:ANY] vdev[0]: Mgt Rate:1000(kbps)[ 49.157119] wlan: [0:I:CMN_MLME] vdev[1] ieee chan:10 freq:2457[ 49.162023] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 49.162023] FD Interval should be a factor of BI.[ 49.162023] Disabling FD[ 49.162023] [ 49.167624] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 49.167624] FD Interval should be a factor of BI.[ 49.167624] Disabling FD[ 49.167624] [ 49.187716] wlan: [0:I:ANY] vdev[1]: Mgt Rate:1000(kbps)[ 49.207562] wlan: [0:I:ANY] vdev[1]: Mgt Rate:1000(kbps)iwpriv ath1 he_ulmumimo 0[ 49.222651] wlan: [5493:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0|dl_muofdma_bfer:0[ 49.222697] wlan: [5493:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x3biwpriv ath1 he_ulofdma 0[ 49.244336] wlan: [5496:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:0|ul_mumimo:0|dl_muofdma_bfer:0[ 49.245799] wlan: [5496:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x1bcfg80211tool ath1 ap_bridge 1wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath1:/var/run/hostapd-ath1.conf[ 49.415427] device ath1 entered promiscuous mode[ 49.416121] br-lan: port 4(ath1) entered forwarding state[ 49.420859] br-lan: port 4(ath1) entered forwarding state[ 49.426574] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-2(ath1):ACS Params[ 49.431535] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:30|chwidth:20|[ 49.439165] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS started: vap:0xffffffc02a4a8000ifconfig ath1 upiw phy phy0 set rts offwlanconfig ath12 create wlandev wifi0 wlanmode ap -cfg80211iw phy phy0 interface add ath12 type __ap[ 49.571427] wlan: [5571:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath12 : clone params: 0x00000001 [ 49.571493] wlan: [5571:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create ba:b0:24:59:b8:0f[ 49.582543] wlan: [5571:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030f60880, opmode=IEEE80211_M_HOSTAP, flags=0x1[ 49.582543] [ 49.590914] wlan: [5571:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1[ 49.603112] wlan: [5571:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0[ 49.610233] wlan: [5571:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b[ 49.625489] wlan: [5571:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged[ 49.632266] wlan: [5571:I:ANY] MBO Initialized[ 49.646335] wlan: [5571:I:ANY] OCE Initialized[ 49.650827] wlan: [5571:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO:1|LRO:0[ 49.656551] wlan: [5571:I:ANY] VAP device ath12 created osifp: (ffffffc02b304880) os_if: (ffffffc02a580000)cfg80211tool ath12 mode 11AHE80cfg80211tool ath12 mode 11AHE80cfg80211tool ath12 channel 0cfg80211tool ath12 hide_ssid 1cfg80211tool ath12 dynamicbeacon 0cfg80211tool ath12 disablecoext 1iw ath12 set 4addr oncfg80211tool ath12 wds 1cfg80211tool ath12 backhaul 0cfg80211tool ath12 uapsd 1cfg80211tool ath12 vap_ind 0cfg80211tool ath12 extap 0iw ath12 set 4addr oncfg80211tool ath12 stafwd 0cfg80211tool ath12 maxsta 128[ 50.113671] wlan: [5634:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128cfg80211tool ath12 blockdfschan 1cfg80211tool ath12 twt_responder 0cfg80211tool ath12 rrm 1cfg80211tool ath12 athnewind 1cfg80211tool ath12 rept_spl 0cfg80211tool ath12 ap_bridge 1wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath12:/var/run/hostapd-ath12.conf[ 50.498032] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-3(ath12):ACS Params[ 50.498858] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:30|chwidth:20|[ 50.506392] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS started: vap:0xffffffc02a580000ifconfig ath12 upiw phy phy0 set rts off[ 50.545215] Not a Hy-Fi device, or device not found: br-iptv[ 50.545696] Not a Hy-Fi device, or device not found: br-iptvqcawifi qcawificfg80211: enable radio wifi2echo -n /ini > /sys/module/firmware_class/parameters/pathupdate_ini_file cfg80211_config=1update_ini_file qwrap_enable=0update_ini_file nss_wifi_olcfg=3update_ini_file rx_hash=0[ 50.708326] wlan: [2583:I:ANY] vap-2(ath1): ACS result PCH 48 freq 5240, SCH 36 freq 5180, hw_mode 2 chwidth 80, vht_seg0 42 freq 5210, vht_seg1 0 freq 0[ 50.708431] wlan: [2583:I:ANY] vap-3(ath12): ACS result PCH 48 freq 5240, SCH 36 freq 5180, hw_mode 2 chwidth 80, vht_seg0 42 freq 5210, vht_seg1 0 freq 0[ 50.721318] wlan: [2583:I:ANY] ieee80211_acs_scan_evhandler: 3885: lock held duration: 13(ms)[ 50.744494] wlan: [954:I:ANY] DES SSID SET=deco[ 50.744523] wlan: [954:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 30[ 50.747968] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 50.747968] Channel is configured already!![ 50.784793] wlan: [0:I:CMN_MLME] vdev[2] ieee chan:48 freq:5240[ 50.785015] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 50.785015] FD Interval should be a factor of BI.[ 50.785015] Disabling FD[ 50.785015] [ 50.789681] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 50.789681] FD Interval should be a factor of BI.[ 50.789681] Disabling FD[ 50.789681] [ 50.793247] wlan: [954:I:ANY] DES SSID SET=zEQQkhpPcoaHsP34[ 50.793254] wlan: [954:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 30[ 50.793353] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 50.793353] Channel is configured already!![ 50.793539] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_set_current_channel_for_freq: 879: dfs_curchan already updated[ 50.853264] wlan: [0:I:ANY] vdev[2]: Mgt Rate:6000(kbps)[ 50.863910] wlan: [0:I:ANY] vdev[2]: Mgt Rate:6000(kbps)[ 50.870219] wlan: [0:I:CMN_MLME] vdev[3] ieee chan:48 freq:5240[ 50.874794] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 50.874794] FD Interval should be a factor of BI.[ 50.874794] Disabling FD[ 50.874794] [ 50.880377] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.[ 50.880377] FD Interval should be a factor of BI.[ 50.880377] Disabling FD[ 50.880377] [ 50.900504] wlan: [0:I:ANY] vdev[3]: Mgt Rate:6000(kbps)[ 50.920355] wlan: [0:I:ANY] vdev[3]: Mgt Rate:6000(kbps)echo q6mem > /sys/bus/coresight/devices/coresight-tmc-etr/out_modeecho 1 > /sys/bus/coresight/devices/coresight-tmc-etr/curr_s[ 51.492436] coresight-funnel 6130000.funnel: FUNNEL inport 5 enabled[ 51.497337] coresight-funnel 6021000.funnel: FUNNEL inport 6 enabled[ 51.504745] coresight-tmc 6028000.tmc: TMC enabled[ 51.507606] coresight-replicator-qcom 6026000.replicator: REPLICATOR enabled[ 51.512209] coresight-tmc 6027000.tmc: TMC enabled[ 51.519421] coresight-funnel 6021000.funnel: FUNNEL inport 7 enabled[ 51.524056] coresight-stm 6002000.stm: STM tracing enabledinkecho 5 > /sys/bus/coresight/devices/coresight-funnel-mm/funnel_ctrlecho 6 > /sys/bus/coresight/devices/coresight-funnel-in0/funnel_ctrlecho 1 > /sys/bus/coresight/devices/coresight-stm/enable*****QDSS Tracing Configuration completed*******echo -e qdss_trace_load_config\nqdss_trace_start\nquit\n > /tmp/qdss_trace_commands******Starting cnss_cli********whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:1 backhual_iface:wifiwhc (repacd): 2g interfaces:ath02, 5g interfaces:ath12whc (repacd): plc interfaces:interface5g:ath12whc (repacd): ath12.1 does not exist, add it.[ 51.914077] device ath12.1 entered promiscuous mode[ 51.918134] device ath12 entered promiscuous mode[ 51.918530] br-lan: port 5(ath12.1) entered forwarding state[ 51.922681] br-lan: port 5(ath12.1) entered forwarding stateinterface2g:ath02whc (repacd): ath02.1 does not exist, add it.[ 51.972094] device ath02.1 entered promiscuous mode[ 51.976114] device ath02 entered promiscuous mode[ 51.976401] br-lan: port 6(ath02.1) entered forwarding state[ 51.980689] br-lan: port 6(ath02.1) entered forwarding statewhc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:2 backhual_iface:wifiwhc (repacd): 2g interfaces:ath02, 5g interfaces:ath12whc (repacd): plc interfaces:interface5g:ath12whc (repacd): ath12.2 does not exist, add it.[ 52.094301] device ath12.2 entered promiscuous mode[ 52.097019] br-lan: port 7(ath12.2) entered forwarding state[ 52.098003] br-lan: port 7(ath12.2) entered forwarding stateinterface2g:ath02whc (repacd): ath02.2 does not exist, add it.[ 52.149687] device ath02.2 entered promiscuous mode[ 52.152646] br-lan: port 8(ath02.2) entered forwarding state[ 52.153387] br-lan: port 8(ath02.2) entered forwarding statewhc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:1 backhual_iface:plcwhc (repacd): 2g interfaces:, 5g interfaces:whc (repacd): plc interfaces:whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:2 backhual_iface:plcwhc (repacd): 2g interfaces:, 5g interfaces:whc (repacd): plc interfaces:whc (repacd): set wifi done flagwhc (repacd): unlock whc_wifi_config_lockwhc (repacd): get whc_wifi_config_lockwhc (repacd): clear wifi_set_done flagwhc (repacd): starting WHC auto-configurationwhc (repacd): Managed network: lanwhc (repacd): Device type: APwhc (repacd): Sysmode: Routerwhc (repacd): the guest network version of the device is latest, we do nothing(uci_revert_state wifi guest enable)whc (repacd): Using SON mode for GW Connected APwhc (repacd): __repacd_restart_dependencies: No changes; not restarting network stack...whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:1 backhual_iface:wifiwhc (repacd): 2g interfaces:ath02, 5g interfaces:ath12whc (repacd): plc interfaces:interface5g:ath12whc (repacd): ath12.1 already existed, do nothing.interface2g:ath02whc (repacd): ath02.1 already existed, do nothing.whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:2 backhual_iface:wifiwhc (repacd): 2g interfaces:ath02, 5g interfaces:ath12whc (repacd): plc interfaces:interface5g:ath12whc (repacd): ath12.2 already existed, do nothing.interface2g:ath02whc (repacd): ath02.2 already existed, do nothing.whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:1 backhual_iface:plcwhc (repacd): 2g interfaces:, 5g interfaces:whc (repacd): plc interfaces:whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:2 backhual_iface:plcwhc (repacd): 2g interfaces:, 5g interfaces:whc (repacd): plc interfaces:whc (repacd): set wifi done flagwhc (repacd): unlock whc_wifi_config_lock[aviraSentinelFull]: stop IS_AVIRA_SENTINEL_FULL_RESTART: 0 [aviraSentinelLite]: stop IS_AVIRA_SENTINEL_LITE_RESTART: 0 [ flowstat_start_timer ] 677: ===> last_up_time=0 iptv.init start iptviptv start_service switch: reset_wan_vlan: select p4: 1switch: reset_wan_vlan: select p5: 2mac:B4-B0-24-59-B8-0C1cap_mac:1[ 54.394821] ivalue value:[ 54.394842] bind_divece_num:1[ 7432] [init 340] init nds:0x0 wanDetect: INFO: wandetect_get_profile_eths:wanDetect: INFO: eth0wanDetect: INFO: eth1[ 7432] [dns_proxy_execFormatCmd 88] cmd: nat del dns wanDetect: INFO: my device_id : 80198A32723C173A21C35791744A5A151F4D05B6wanDetect: INFO: init_no_wan_modewanDetect: INFO: clear_dialed_flagwanDetect: INFO: move all interface to br-lan wanDetect: INFO: move eth0 to br-lan...[ 7432] [dns_proxy_execFormatCmd 88] cmd: nat add dns { 192.168.68.1 0.0.0.0 } conn-indicator: INFO: -- running --conn-indicator: NOTE: BINDING state: -1 -> 3conn-indicator: INFO: <30000307> Invoke led: conn[2]conn-indicator: NOTE: Mode changed: Unknown -> Routerconn-indicator: NOTE: Role changed: Unknown -> FAPconn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directoryconn-indicator: ERR: Invalid directory: /tmp/sync-serverconn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_listconn-indicator: ERR: Failed to allocate DEV_LISTconn-indicator: NOTE: Network type: Unknown -> FAPconn-indicator: INFO: <31330307> Invoke led: conn[1]conn-indicator: NOTE: Connectivity changed: FAP.LOST(0x7) -> OFFLINE(0x1)wandetect: move eth0 to other bridgewandetect: move eth0 to lan bridgedevice eth0 is not a slave of br-wandevice eth0 is already a member of a bridge; can't enslave it to bridge br-lan.===== TIPC have already enabled ==== [ 7432] [dns_proxy_execFormatCmd 88] cmd: nat add dns { 0.0.0.0 0.0.0.0 } wanDetect: INFO: move eth1 to br-lan...[ 7432] [main 481] init done, now do uloop_run [ 54.716004] Started in network mode[ 54.716031] Own node address <224.3584.1>, network identity 4711[ 54.725041] Enabled bearer <deco:br-lan:1>, discovery domain <224.3584.0>, priority 10wandetect: move eth1 to other bridgewandetect: move eth1 to lan bridgedevice eth1 is not a slave of br-wandevice eth1 is already a member of a bridge; can't enslave it to bridge br-lan.wanDetect: INFO: Goto uloop_runtipc-server: INFO: -- running --tipc-server: INFO: server radar: port {18888,100,200} createdtipc-server: INFO: mode is APtipc-server: INFO: mode is APtipc-server: INFO: server AP: port {5000,100,100} createdtipc-server: INFO: mode is AP[ 54.784496] Not a Hy-Fi device, or device not found: br-iptv[ 54.786621] Not a Hy-Fi device, or device not found: br-iptvconn-indicator: INFO: Notify inet.downjson_object_from_file: error reading file /tmp/sync-server/mesh_dev_list: No such file or directorysmart_home_schedule reload_servicemaclist_smart_home:#### no schedule client found in blacklist config ####[ 55.072358] S95done (7851): drop_caches: 3conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directoryconn-indicator: ERR: Invalid directory: /tmp/sync-serverconn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_listconn-indicator: ERR: Failed to allocate DEV_LISTmanager permission has been set, no need to set again guest-eth: Start to set guest vlanguest-eth: Ignore system signalguest-eth: Lock vlan.lockguest-eth: AP role, eth0 eth1 set tag port, vlan id is 591guest-eth: add eth if eth0.591[ 56.215089] device eth0.591 entered promiscuous mode[ 56.222165] IPv6: ADDRCONF(NETDEV_UP): eth0.591: link is not readyguest-eth: add eth if eth1.591[ 56.239741] device eth1.591 entered promiscuous mode[ 56.246461] IPv6: ADDRCONF(NETDEV_UP): eth1.591: link is not readymac:B4-B0-24-59-B8-0Crole:APupdate fap: B4:B0:24:59:B8:0C[ 56.389241] net rmnet_mhi0: link_state 0x0 -> 0x1[ 56.391828] IPv6: ADDRCONF(NETDEV_CHANGE): rmnet_mhi0: link becomes ready[ 56.393075] IPv6: ADDRCONF(NETDEV_CHANGE): rmnet_mhi0.1: link becomes readyconn-indicator: INFO: <31330301> link event: rmnet_mhi0.upwanDetect: INFO: --> link event: rmnet_mhi0.upwanDetect: INFO: ! mode_need_dialconn-indicator: INFO: <31330301> link event: rmnet_mhi0.1.upwanDetect: INFO: --> link event: rmnet_mhi0.1.upwanDetect: INFO: ! mode_need_dialconn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directoryconn-indicator: ERR: Invalid directory: /tmp/sync-serverconn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_listconn-indicator: ERR: Failed to allocate DEV_LIST*****/tmp/ipv6_firewall/op_rule_id file not found, create it.*****[ 56.974641] Not a Hy-Fi device, or device not found: br-iptv[ 56.974734] Not a Hy-Fi device, or device not found: br-iptv[ 3366(lan)] [smartip_ibus_handle_wifi_event 2289] smartipd handle wifi event:9 [ 3366(lan)] [smartip_ibus_handle_wifi_event 2313] RE -> AP [ 3366(lan)] [smartip_ibus_handle_dhcp_server_changed 2204] DHCP Server changed [ 3366(lan)] [smartip_ibus_handle_dhcp_server_changed 2238] Restart dhcpd [ 3366(lan)] [smartip_kill_process 271] kill process udhcpd conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directoryconn-indicator: ERR: Invalid directory: /tmp/sync-serverconn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_listconn-indicator: ERR: Failed to allocate DEV_LIST[ 3366(lan)] [smartip_start_process 366] start udhcpd [ 3366(lan)] [smartip_check_lan_wan_is_samesubnet 2800] br-wan has no ip! [ 3366(lan)] [smartip_ibus_handle_wifi_event 2343] Change to FAP, Update Lan IP [ 3366(lan)] [smartip_notify_lan_update 1320] Notify the lan ip changed. [ 3366(lan)] [smartip_update_lanip 593] config IP: ifconfig br-lan 192.168.68.1 netmask 255.255.252.0 [ 3366(lan)] [smartip_update_lanip 604] route del default dev br-lan [ 58.561785] work mode change to :AP[ 58.561785] [ 58.564769] get dev num:2[ 58.566301] statistics: SET_STA_DEVICE dev_name=eth0[ 58.566304] statistics: SET_STA_DEVICE dev_name=eth1[ 58.566308] backhaul sta dev num:2conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directoryconn-indicator: ERR: Invalid directory: /tmp/sync-serverconn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_listconn-indicator: ERR: Failed to allocate DEV_LISTstart minitor config flowstat_send_test_sms[ 3366(lan)] [smartip_update_lanip 622] restart miniupnpd parental-control_avira: Restart the avira homecare[ 8728(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:UPDATE start minitor config mobile_config[ 8849(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:FAPIPUPDATE not found in configecho 0 to init===parental_control_avira=== no need to start[aviraSentinelFull]: stop IS_AVIRA_SENTINEL_FULL_RESTART: 0 false 0start minitor config profile_action[aviraSentinelLite]: stop IS_AVIRA_SENTINEL_LITE_RESTART: 0 IPConflict2 mask:22 lan_addr:192.168.68.1 mask_str:255.255.252.0IPConflict2 mask:22IPConflict2 old_mask:255.255.252.0 old_ip:192.168.68.1[ 3366(lan)] [smartip_update_lanip 634] restart domain_login [ 59.375519] Not a Hy-Fi device, or device not found: br-iptv[ 59.375636] Not a Hy-Fi device, or device not found: br-iptvqos_v2 disable gro qos_v2 start conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directoryconn-indicator: ERR: Invalid directory: /tmp/sync-serverconn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_listconn-indicator: ERR: Failed to allocate DEV_LISTwanDetect: ERR: port update : eth0/lib/sync-server/scripts/detect-re:35: error open file failed:/var/run/record_devid /lib/sync-server/scripts/detect-re:35: error open file failed:/tmp/sync-server/mesh_dev_list /lib/sync-server/scripts/detect-re:57: error: record_devid or mesh_dev_list is nil, do nothing conn-indicator: ERR: [file_md5sum] fopen(/tmp/sync-server/mesh_dev_list): No such file or directoryjson_object_from_file: error reading file /tmp/sync-server/mesh_dev_list: No such file or directoryconn-indicator: ERR: [update_devlist] Failed to parse /tmp/sync-server/mesh_dev_list: No such file or directory[ 60.738621] mode:0/lib/sync-server/scripts/probe:228: error open file failed:/var/run/record_devid /lib/sync-server/scripts/probe:748: to_get_info 80198A32723C173A21C35791744A5A151F4D05B6 first, clean old record data /lib/sync-server/scripts/probe:752: to_get_info 80198A32723C173A21C35791744A5A151F4D05B6 ========= MODE: cloud_awn_update begin ========== mode: AP Ipv6 Firewall config trigger stop!qos_v2 stop ========= MODE: update awn feature info to cloud ========== --------->exiting qos/lib/sync-server/scripts/probe:861: to_get_info: ["192.168.68.1","1"] conn-indicator: ERR: [update_devlist] Failed to parse /tmp/sync-server/mesh_dev_list: Resource temporarily unavailable/lib/sync-server/scripts/get-info:84: Total 1 devices need to get info sync_get_info begin() sync_get_compatible_info sync_get_info end() error open file failed:/var/run/record_devid error open file failed:/var/run/record_op error open file failed:/var/run/record_cfg error open file failed:/var/run/record_component_router_owner error open file failed:/var/run/record_component_router_user error open file failed:/var/run/record_component_ap_owner error open file failed:/var/run/record_component_ap_user error open file failed:/var/run/record_opcode_cfg error open file failed:/var/run/record_devid error open file failed:/tmp/check_dev error open file failed:/var/run/record_component_whole update_compitable_list can't support IOT /lib/sync-server/scripts/get-info:92: Total 1 devices were got info successfully error open file failed:/var/run/lookup_cfg there is no iot fap error open file failed:/var/run/lookup_op check_opcode_iot fap has no iot /lib/sync-server/scripts/get-info:104: Total 1 devices need to get cfg req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5A151F4D05B6"}} qos_v2 disable gro qos_v2 start sync_get_cfg begin() Warning! can't find cfg : white_list_1 sync_get_cfg end() error open file failed:/tmp/merge_cfgs /lib/sync-server/scripts/get-info:106: Total 1 devices were got cfg successfully /lib/sync-server/scripts/get-info:121: merge_cfgs is nil , don't update user_config. Total 1 devices need to update dev list Total 1 devices were update dev list successfully re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ====== req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5A151F4D05B6"}} re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ====== req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5A151F4D05B6"}} re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ====== notify_check_client: current time is 1681133532 req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5A151F4D05B6"}} client triggers is opened. re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ======
COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING
cat /proc/devicesCharacter devices: 1 mem 5 /dev/tty 5 /dev/console 5 /dev/ptmx 10 misc 13 input 29 fb 89 i2c 90 mtd116 alsa128 ptm136 pts153 spi180 usb189 usb_device239 flash_chrdev241 ubi0242 subsys243 nvme244 ttyMSM245 ttyMSM246 dcc_sram247 mhi_uci248 watchdog249 iio250 ptp251 pps252 rtc253 msm_sps254 rpmsgBlock devices: 1 ramdisk259 blkext 31 mtdblock179 mmc253 ubiblock254 nvmeroot@(none):/#
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
![[OpenWrt Wiki] TP-Link X80-5G V1 (2024)](data:image/png;base64,iVBORw0KGgoAAAANSUhEUgAAAAEAAAABCAQAAAC1HAwCAAAAC0lEQVR42mP8/h8AAvMB+NzmkbcAAAAASUVORK5CYII=)